Compact 33″ Height and Standard Cabinet Widths.

Multi-Position Design With Minimal Conversion Requirements.

Airflow Leakage Rate of Less Than 1% of Total Airflow @ 1″ ESP.

PSC Four-Speed Direct Drive Motor with Large, Quiet Blower.

Fully-Supported, Slide-Out Blower Assembly for Easy Service Access.

Tubular Aluminized Steel Primary Heat Exchanger.

High-Level Self-Diagnostic Controls With Fault Codes.

Sharp Edges Have Been Eliminated By Folding and Flattening the Sheet Metal.

Fully-Gasketed, Independent Access Doors With View Ports.

External Air Filters (Not Included) Provide Flexibility for IAQ Needs.

All Models Are Propane Convertible.

Small Footprint – Minimum footprint for easier handling, transportation, and installation.

Easier Installation – Independent panels provide quick access for unit setup. Installation time is reduced by easy power and control wiring access. Options are provided for indoor piston or TXV. The factory installed filter-drier and factory charge for a 15-ft. lineset means less time spent brazing and charging the system. The small base dimension and reduced unit clearances make for easier retrofits.

Accessible Information – QR code on unit provides quick access to technical documents and warranty information.

Durable Finish – The coated steel wire fan guard, coated external fasteners, and pre-treated G90-equivalent galvanized steel chassis components resist corrosion and rust creep. Titanium colored powdercoat paint further protects external panels.

Quality Coils – The high efficiency microchannel aluminum coil is manufactured using an improved material system providing reliable performance and small unit size.

Reliable Operation – Ball bearing fan motors provide superior performance in extreme temperatures.

Rugged Coil Protection – Coils are protected from mechanical damage by a proven stamped steel coil guard design.

Protected Compressor – Compressors are protected internally by a high pressure relief valve and a temperature sensor, and externally by the system high pressure switch. The liquid line filter-drier is factory installed to protect the compressor against moisture and debris.

Environmentally Friendly – CFC-free R-410A refrigerant delivers environmentally friendly performance with zero ozone depletion.

Top Discharge – Warm air is blown up, away from the structure and any landscaping and allows compact location on multi-unit applications.

Low Operating Sound Levels – Developed using CFD and FEA tools, the sturdy cabinet and top design provides sound performance of 76 dBA or lower. Compatible accessories for further sound reduction are also available.

Better Service Access – Diagonal base valves with open access for low-loss fittings, single panel access to the electrical controls, swing out control box for full corner access, and removable fan guard allow easy access for unit maintenance.

Agency Listed – Safety certified by CSA to UL 1995/CSA 22.2. Performance certified to ANSI/AHRI Standard 210/240 in accordance with the Unitary Small Equipment certification program.

Small Footprint – extremely lightweight with a compact footprint, it will be a perfect fit for any application.

Quality Condenser Coils – The coil is constructed of aluminum microchannel tubing and enhanced aluminum fins for increased efficiency.

Coil Protection – Coils are protected from damage by a polymer mesh applied between the coil face, and a coated steel coil guard.

Protected Compressor – Compressors are internally protected against high pressure and temperature. This is accomplished by the simultaneous operation of high pressure relief valve and a temperature sensor which protects the compressor if undesirable operating conditions occur. A liquid line filter-drier further protects the compressor.

Durable Finish – The cabinet is made of pre-painted steel. The pre-treated flat galvanized steel provides a better paint-to-steel bond, which resists corrosion and rust creep. Special primer formulas and matted champagne finish insure less fading when exposed to sunlight.

Lower Installed Cost – Installation time and costs are reduced by easy power and control wiring connections. The small base dimension means less space is required on the ground or roof.

Top Discharge – The warm air from the top mounted fan is blown away from the structure and any landscaping. This allows compact location on multi-unit applications.

Low Operating Sound Level – The upward air flow carries the normal operating noise away from the living area. The rigid top panel effectively isolates any motor sound. Isolator mounted compressor and the condenser coil muffle the normal fan motor and compressor operating sounds.

Low Maintenance – Long life permanently lubricated motor-bearings need no annual servicing.

Easy Service Access – Fully exposed refrigerant connections and a single panel covering the electrical controls make for easy servicing of the unit.

Secured Service Valves – Secured re-usable service valves are provided on both the liquid and vapor sweat connections for ease of evacuating and charging.

U.L. and C.U.L Listed – Approved for outdoor application. Certified in accordance with the Unitary Small Equipment certification program, which is based on ARI Standard 210/240.

Small Footprint – extremely lightweight with a compact footprint, it will be a perfect fit for any application.

Quality Condenser Coils – The coil is constructed of aluminum microchannel tubing and enhanced aluminum fins for increased efficiency.

Coil Protection – Coils are protected from damage by a polymer mesh applied between the coil face, and a coated steel coil guard.

Protected Compressor – Compressors are internally protected against high pressure and temperature. This is accomplished by the simultaneous operation of high pressure relief valve and a temperature sensor which protects the compressor if undesirable operating conditions occur. A liquid line filter-drier further protects the compressor.

Durable Finish – The cabinet is made of pre-painted steel. The pre-treated flat galvanized steel provides a better paint-to-steel bond, which resists corrosion and rust creep. Special primer formulas and matted champagne finish insure less fading when exposed to sunlight.

Lower Installed Cost – Installation time and costs are reduced by easy power and control wiring connections. The small base dimension means less space is required on the ground or roof.

Top Discharge – The warm air from the top mounted fan is blown away from the structure and any landscaping. This allows compact location on multi-unit applications.

Low Operating Sound Level – The upward air flow carries the normal operating noise away from the living area. The rigid top panel effectively isolates any motor sound. Isolator mounted compressor and the condenser coil muffle the normal fan motor and compressor operating sounds.

Low Maintenance – Long life permanently lubricated motor-bearings need no annual servicing.

Easy Service Access – Fully exposed refrigerant connections and a single panel covering the electrical controls make for easy servicing of the unit.

Secured Service Valves – Secured re-usable service valves are provided on both the liquid and vapor sweat connections for ease of evacuating and charging.

U.L. and C.U.L Listed – Approved for outdoor application. Certified in accordance with the Unitary Small Equipment certification program, which is based on ARI Standard 210/240.

Quality Coils – Enhanced aluminum fins are mechanically bonded to copper tubing.

Scroll Compressor – Featuring the newest generation of high efficiency scroll compressors.

Copper filter-drier – The factory installed filter drier features copper construction for reliable long term protection.

Easier Installation – Independent panels provide quick access for unit setup. Installation time is reduced by easy power and control wiring access. Select indoor matches with factory-mounted TXVs are available for quicker system installation. The factory installed filter-drier and factory charge for a 15-ft. lineset means less time spent brazing and charging the system. The small base dimension and reduced unit clearances make for easier retrofits.

Accessible Information – QR code on unit provides quick access to technical documents and warranty information. Durable Finish – The coated steel wire fan guard, coated external fasteners, and pre-treated G90-equivalent galvanized steel chassis components resist corrosion and rust creep. Titanium colored powdercoat paint further protects external panels.

Rugged Coil Protection – Coils are protected from mechanical damage by a proven stamped steel coil guard design.

Protected Compressor – Compressors are protected internally by a high pressure relief valve and a temperature sensor, and externally by the system high pressure switch. The liquid line filter-drier is factory installed to protect the compressor against moisture and debris.

Reliable Operation – Ball bearing fan motors provide superior performance in extreme temperatures. Environmentally Friendly – CFC-free R-410A refrigerant delivers environmentally friendly performance with zero ozone depletion.

Top Discharge – Warm air is blown up, away from the structure and any landscaping and allows compact location on multi-unit applications.

Low Operating Sound Levels – Developed using CFD and FEA tools, the sturdy cabinet and top design provides sound performance of 76 dBA or lower. Compatible accessories for further sound reduction are also available.

Better Service Access – Diagonal base valves with open access for low-loss fittings, single panel access to the electrical controls, swing out control box for full corner access, and removable fan guard allow easy access for unit maintenance.

Agency Listed – Approved for outdoor application. Certified in accordance with the Unitary Small Equipment certification program, which is based on ARI Standard 210/240.

Energy Star Certified.

Small Footprint – extremely lightweight with a compact footprint, it will be a perfect fit for any application.

Quality Condenser Coils – The coil is constructed of aluminum microchannel tubing and enhanced aluminum fins for increased efficiency.

Coil Protection – Coils are protected from damage by a polymer mesh applied between the coil face, and a coated steel coil guard.

Protected Compressor – Compressors are internally protected against high pressure and temperature. This is accomplished by the simultaneous operation of high pressure relief valve and a temperature sensor which protects the compressor if undesirable operating conditions occur. A liquid line filter-drier further protects the compressor.

Durable Finish – The cabinet is made of pre-painted steel. The pre-treated flat galvanized steel provides a better paint-to-steel bond, which resists corrosion and rust creep. Special primer formulas and matted champagne finish insure less fading when exposed to sunlight.

Lower Installed Cost – Installation time and costs are reduced by easy power and control wiring connections. The small base dimension means less space is required on the ground or roof.

Top Discharge – The warm air from the top mounted fan is blown away from the structure and any landscaping. This allows compact location on multi-unit applications.

Low Operating Sound Level – The upward air flow carries the normal operating noise away from the living area. The rigid top panel effectively isolates any motor sound. Isolator mounted compressor and the condenser coil muffle the normal fan motor and compressor operating sounds.

Low Maintenance – Long life permanently lubricated motor-bearings need no annual servicing.

Easy Service Access – Fully exposed refrigerant connections and a single panel covering the electrical controls make for easy servicing of the unit.

Secured Service Valves – Secured re-usable service valves are provided on both the liquid and vapor sweat connections for ease of evacuating and charging.

U.L. and C.U.L Listed – Approved for outdoor application. Certified in accordance with the Unitary Small Equipment certification program, which is based on ARI Standard 210/240.

Energy Star Certified.

Performance – Efficiency levels from 13.0 SEER/11.0 EER with a loose coil up to 16.0 SEER/14.0 EER (some models) when coupled with an ECM indoor blower.

Small Footprint – Compact “slim-line” design allows for easy installation in tight spaces. Units can be stacked two-high with approved stacking kit.

Sound Reducing System – The combination of a swept-wing fan, rigid base pan, isolated compressor compartment, and quiet scroll compressor reduce sound to as low as 67 dBA.

Low Operating Sound Levels – The swept-wing condenser fan in blow-through configuration provides for whisper-quiet operation by allowing air to flow smoothly and efficiently across the fan tips.

Quality Condenser Coils – The coil is constructed of aluminum microchannel tubing and enhanced aluminum fins for compact size and increased efficiency.

Environmentally Friendly Refrigerant – The next generation refrigerant R-410A delivers environmentally friendly performance with zero ozone depletion.

Durable Cabinet – Heavy-gage steel cabinet and tubular base rails provide added support.

Aesthetic – Powder paint “Champagne” color provides an attractive retail finish.

Agency Listed – Safety certified by CSA to UL 1995/CSA 22.2. Performance certified to ANSI/AHRI Standard 210/240 in accordance with the Unitary Small Equipment certification program.

Performance – Efficiency levels from 13.0 SEER/11.0 EER with a loose coil up to 16.0 SEER/14.0 EER (some models) when coupled with an ECM indoor blower.

Small Footprint – Compact “slim-line” design allows for easy installation in tight spaces. Units can be stacked two-high with approved stacking kit.

Sound Reducing System – The combination of a swept-wing fan, rigid base pan, isolated compressor compartment, and quiet scroll compressor reduce sound to as low as 67 dBA.

Low Operating Sound Levels – The swept-wing condenser fan in blow-through configuration provides for whisper-quiet operation by allowing air to flow smoothly and efficiently across the fan tips.

Quality Condenser Coils – The coil is constructed of aluminum microchannel tubing and enhanced aluminum fins for compact size and increased efficiency.

Environmentally Friendly Refrigerant – The next generation refrigerant R-410A delivers environmentally friendly performance with zero ozone depletion.

Durable Cabinet – Heavy-gage steel cabinet and tubular base rails provide added support.

Aesthetic – Powder paint “Champagne” color provides an attractive retail finish.

Agency Listed – Safety certified by CSA to UL 1995/CSA 22.2. Performance certified to ANSI/AHRI Standard 210/240 in accordance with the Unitary Small Equipment certification program.

Superior Coil Protection – A stamped, decorative metal coil guard completely protects the coil from debris and other damaging material.

Protected Compressor – The compressor is safeguarded against abnormal pressures and temperatures by an internal pressure relief valve, an internal temperature sensor, and factory high and low pressure system controls. A factory installed liquid line filter-drier further protects the compressor against moisture and debris.

Environmentally Friendly Refrigerant – The next generation refrigerant R-410A delivers environmentally friendly performance with zero ozone depletion.

Durable Finish – An automotive quality finish provides the ultimate protection from harmful UV rays and rust creep, ensuring a long-lasting, high quality appearance. A powder-paint topcoat is applied over a baked-on primer using a galvanized, zinc coated steel base material. The result is a finish that has been proven in testing to provide 33% greater durability than conventional powder-coat finishes.

Sound Reducing System – Features combination of swept-wing fan, composite base pan, isolated compressor compartment, and single-stage compressor to reduce overall sound to a mere whisper.

Low RPM Fan Motor – Helps to reduce airflow noise.

Swept Wing Fan – A fan design boasting technology adapted from aeronautic and defense engineering provides for whisper-quiet operation by allowing air to flow smoothly and efficiently across the fan tips.

Composite Base Pan – The strong and durable composite base pan provides added strength while resisting rust and corrosion, as well as reducing sound and vibration.

Isolated Compressor Compartment – A molded composite bulkhead isolates the refrigeration components and the compressor from the rest of the unit, reducing sound and vibration.

Lower Installed Cost – Designed to provide enhanced installability by featuring a slide-down control compartment that allows easy access to control components, along with angled service valves to reduce overall installation time and cost.

Factory Installed Filter-Drier – A factory installed, solid core liquid line filter-drier removes harmful debris and moisture from the system.

Easy Service Access – A full end, full service access panel with handle makes for easy entry to internal components.

Communications Capable – Requiring only a simple 4-wire installation, the communicating capability enables the use of the Touch Screen Communicating Control, allowing real time visibility of system operation and the use of diagnostic features, while still maintaining the ability to function with a traditional thermostat.

Agency Listed – Safety certified by CSA to UL 1995/CSA 22.2. Performance certified to ANSI/AHRI Standard 210/240 in accordance with the Unitary Small Equipment certification program.

Superior Coil Protection – A stamped, decorative metal coil guard completely protects the coil from debris and other damaging material.

Protected Compressor – The compressor is safeguarded against abnormal pressures and temperatures by an internal pressure relief valve, an internal temperature sensor, and factory high and low pressure system controls. A factory installed liquid line filter-drier further protects the compressor against moisture and debris.

Environmentally Friendly Refrigerant – The next generation refrigerant R-410A delivers environmentally friendly performance with zero ozone depletion.

Durable Finish – An automotive quality finish provides the ultimate protection from harmful UV rays and rust creep, ensuring a long-lasting, high quality appearance. A powder-paint topcoat is applied over a baked-on primer using a galvanized, zinc coated steel base material. The result is a finish that has been proven in testing to provide 33% greater durability than conventional powder-coat finishes.

Sound Reducing System – Features combination of swept-wing fan, composite base pan, isolated compressor compartment, and single-stage compressor to reduce overall sound to a mere whisper.

Low RPM Fan Motor – Helps to reduce airflow noise.

Swept Wing Fan – A fan design boasting technology adapted from aeronautic and defense engineering provides for whisper-quiet operation by allowing air to flow smoothly and efficiently across the fan tips.

Composite Base Pan – The strong and durable composite base pan provides added strength while resisting rust and corrosion, as well as reducing sound and vibration.

Isolated Compressor Compartment – A molded composite bulkhead isolates the refrigeration components and the compressor from the rest of the unit, reducing sound and vibration.

Lower Installed Cost – Designed to provide enhanced installability by featuring a slide-down control compartment that allows easy access to control components, along with angled service valves to reduce overall installation time and cost.

Factory Installed Filter-Drier – A factory installed, solid core liquid line filter-drier removes harmful debris and moisture from the system.

Easy Service Access – A full end, full service access panel with handle makes for easy entry to internal components.

Communications Capable – Requiring only a simple 4-wire installation, the communicating capability enables the use of the Touch Screen Communicating Control, allowing real time visibility of system operation and the use of diagnostic features, while still maintaining the ability to function with a traditional thermostat.

Agency Listed – Safety certified by CSA to UL 1995/CSA 22.2. Performance certified to ANSI/AHRI Standard 210/240 in accordance with the Unitary Small Equipment certification program.

Small Footprint – extremely lightweight with a compact footprint, it will be a perfect fit for any application.

Quality Condenser Coils – The coil is constructed of copper tubing and enhanced aluminum fins for increased performance.

Coil Protection – Coils are protected from damage by a polymer mesh applied between the coil face, and a coated steel coil guard.

Protected Compressor – The compressor is protected internally by a high pressure relief valve and a temperature sensor, and externally by the system high and low pressure switches. A factory installed liquid line filter-drier further protects the compressor against moisture and debris.

Environmentally Friendly Refrigerant – The next generation refrigerant R-410A delivers environmentally friendly performance with zero ozone depletion.

Durable Finish – The cabinet is made of G90-equivalent pre-painted steel, with special primer formulas and matte champagne texture to insure less fading when exposed to sunlight. The coated steel wire fan and coil guards and pre-treated, galvanized steel chassis components resist corrosion and rust creep.

Lower Installed Cost – Installation time and costs are reduced by easy power and control wiring connections. The unit is factory charged for a 15-foot lineset. The small base dimension means less space is required on the ground or roof.

Top Discharge – Warm air from the top mounted fan is blown up, away from the structure and any landscaping. This allows compact location on multi-unit applications.

Low Operating Sound Level – The upward air flow carries the normal operating noise away from the living area. The rigid top panel effectively isolates any motor sound. Isolator mounted compressor and the condenser coil muffle the normal fan motor and compressor operating sounds.

Low Maintenance – Long life, permanently lubricated motor-bearings need no annual servicing.

Easy Service Access – Fully exposed refrigerant connections and a single panel covering the electrical controls make for easy servicing of the unit.

Secured Service Valves – Secured, re-usable service valves are provided on both the liquid and vapor sweat connections for ease of evacuating and charging.

Agency Listed – Safety certified by CSA to UL 1995/CSA 22.2. Performance certified to ANSI/AHRI Standard 210/240 in accordance with the Unitary Small Equipment certification program.

Small Footprint – The compact footprint is a perfect fit for any application.

Quality Condenser Coils – The coil is constructed of copper tubing and enhanced aluminum fins for increased performance.

Coil Protection – Coils are protected from damage by a slotted, stamped steel coil guard.

Protected Compressor – Compressors are protected internally by a high pressure relief valve and a temperature sensor, and externally by the system high and low pressure switches. A factory installed liquid line filter-drier further protects the compressor against moisture and debris.

Durable Finish – The cabinet is made of G90-equivalent galvanized steel, finished in a durable titanium colored powdercoat. The coated steel wire fan guard and pre-treated, galvanized steel chassis components resist corrosion and rust creep.

Lower Installed Cost – Installation time and costs are reduced by easy power and control wiring connections. The unit is factory charged for a 15-foot lineset. The small base dimension means less space is required on the ground or roof.

Top Discharge – Warm air from the top mounted fan is blown up, away from the structure and any landscaping. This allows compact location on multi-unit applications.

Quiet Operation – The compressor sound blanket and the swept wing fan blade keep sound to a minimum. The upward air flow carries the normal operating noise away from the living area. The rigid top panel effectively isolates any motor sound. Isolator mounted compressor and the condenser coil muffle the normal fan motor and compressor operating sounds. The rigid top panel effectively isolates any motor sound. Isolator mounted compressor and the condenser coil muffle the normal fan motor and compressor operating sounds.

Low Maintenance – Long life, permanently lubricated motor-bearings need no annual servicing.

Easy Service Access – Fully exposed refrigerant connections and a single panel covering the electrical controls make for easy servicing of the unit.

Advanced System Control –  These heat pumps feature a demand-defrost control system to provide optimal comfort and reliable operation over a wide range of conditions.

Secured Service Valves – Secured, re-usable service valves are provided on both the liquid and vapor sweat connections for ease of evacuating and charging.

Agency Listed – Safety certified by CSA to UL 1995/CSA 22.2. Performance certified to ANSI/AHRI Standard 210/240 in accordance with the Unitary Small Equipment certification program.

Energy Star Certified.

Superior Coil Protection – A stamped, decorative metal coil guard protects the tube-in-fin coil from debris and other damaging material.

Protected Compressor – The compressor is safeguarded against abnormal pressures and temperatures by an internal pressure relief valve, an internal temperature sensor, and factory high and low pressure system controls. A factory installed liquid line filter-drier further protects the compressor against moisture and debris.

Environmentally Friendly Refrigerant – TThe next generation refrigerant R-410A delivers environmentally friendly performance with zero ozone depletion.

Durable Finish – An automotive quality finish provides the ultimate protection from harmful UV rays and rust creep, ensuring a long-lasting, high quality appearance. A powder-paint topcoat is applied over a baked-on primer using a galvanized, zinc coated steel base material. The result is a finish that has been proven in testing to provide 33% greater durability than conventional powder-coat finishes.

Hot Heat Pump – An optional mode that slows the indoor fan for higher register air temperatures and premium comfort.

Sound Reducing System – Features combination of swept-wing fan, composite base pan, isolated compressor compartment, and single-stage compressor to reduce overall sound to a mere whisper.

Low RPM Fan Motor – Helps to reduce airflow noise.

Swept Wing Fan – A fan design boasting technology adapted from aeronautic and defense engineering provides for whisper-quiet operation by allowing air to flow smoothly and efficiently across the fan tips.

Composite Base Pan – The strong and durable composite base pan provides added strength while resisting rust and corrosion, as well as reducing sound and vibration.

Isolated Compressor Compartment – A molded composite bulkhead isolates the refrigeration components and the compressor from the rest of the unit, reducing sound and vibration.

Lower Installed Cost – Designed to provide enhanced installability by featuring a slide-down control compartment that allows easy access to control components, along with angled service valves to reduce overall installation time and cost. Factory charged for a 15 foot lineset.

Factory Installed Filter-Drier – A factory installed, solid core liquid line filter-drier removes harmful debris and moisture from the system.

Easy Service Access – A full end, full service access panel with handle makes for easy entry to internal components.

Communications Capable – Requiring only a simple 4-wire installation, the communicating capability enables the use of the Touch Screen Communicating Control, allowing real time visibility of system operation and the use of diagnostic features, while still maintaining the ability to function with a traditional thermostat.

Complete System Control – These heat pumps utilize a unique microprocessor defrost control system to provide optimal comfort as well as monitor the overall system for reliable operation. In the event improper operating conditions occur (high temperature and/or high pressure), the system will automatically shut the system down to extend the life of the heat pump. The defrost control features an internal memory to aid the technician in troubleshooting, reducing service time and cost.

Agency Listed – Safety certified by CSA to UL 1995/CSA 22.2. Performance certified to ANSI/AHRI Standard 210/240 in accordance with the Unitary Small Equipment certification program.

Superior Coil Protection – A stamped, decorative metal coil guard protects the tube-in-fin coil from debris and other damaging material.

Protected Compressor – The compressor is safeguarded against abnormal pressures and temperatures by an internal pressure relief valve, an internal temperature sensor, and factory high and low pressure system controls. A factory installed liquid line filter-drier further protects the compressor against moisture and debris.

Environmentally Friendly Refrigerant – TThe next generation refrigerant R-410A delivers environmentally friendly performance with zero ozone depletion.

Durable Finish – An automotive quality finish provides the ultimate protection from harmful UV rays and rust creep, ensuring a long-lasting, high quality appearance. A powder-paint topcoat is applied over a baked-on primer using a galvanized, zinc coated steel base material. The result is a finish that has been proven in testing to provide 33% greater durability than conventional powder-coat finishes.

Hot Heat Pump – An optional mode that slows the indoor fan for higher register air temperatures and premium comfort.

Sound Reducing System – Features combination of swept-wing fan, composite base pan, isolated compressor compartment, and single-stage compressor to reduce overall sound to a mere whisper.

Low RPM Fan Motor – Helps to reduce airflow noise.

Swept Wing Fan – A fan design boasting technology adapted from aeronautic and defense engineering provides for whisper-quiet operation by allowing air to flow smoothly and efficiently across the fan tips.

Composite Base Pan – The strong and durable composite base pan provides added strength while resisting rust and corrosion, as well as reducing sound and vibration.

Isolated Compressor Compartment – A molded composite bulkhead isolates the refrigeration components and the compressor from the rest of the unit, reducing sound and vibration.

Lower Installed Cost – Designed to provide enhanced installability by featuring a slide-down control compartment that allows easy access to control components, along with angled service valves to reduce overall installation time and cost. Factory charged for a 15 foot lineset.

Factory Installed Filter-Drier – A factory installed, solid core liquid line filter-drier removes harmful debris and moisture from the system.

Easy Service Access – A full end, full service access panel with handle makes for easy entry to internal components.

Communications Capable – Requiring only a simple 4-wire installation, the communicating capability enables the use of the Touch Screen Communicating Control, allowing real time visibility of system operation and the use of diagnostic features, while still maintaining the ability to function with a traditional thermostat.

Complete System Control – These heat pumps utilize a unique microprocessor defrost control system to provide optimal comfort as well as monitor the overall system for reliable operation. In the event improper operating conditions occur (high temperature and/or high pressure), the system will automatically shut the system down to extend the life of the heat pump. The defrost control features an internal memory to aid the technician in troubleshooting, reducing service time and cost.

Agency Listed – Safety certified by CSA to UL 1995/CSA 22.2. Performance certified to ANSI/AHRI Standard 210/240 in accordance with the Unitary Small Equipment certification program.

RC2 –  Rigid Case Construction interior endoskeleton provides structural support, flush sides, and locks in insulation.

Powder-painted – G30 galvanized steel case provides a coated edge that resists corrosion and rust creep.

Quality Construction – Structural components are made of Aluminum or G90 galvanized steel to prevent corrosion.

Improved Insulation Design – Single piece with no external screws to reduce thermal transmission paths to prevent sweating. Foil faced insulation for ease of cleaning.

Case Depth – These models have 20.5″ casing which provide ease of attic access and tight applications.

Factory Sealed – Achieves 2% or less total airflow leakage rate at duct leakage test conditions in positive and negative pressure for system airflow verification.

Electric Heat Kits –  6HK series of field installed electric heat kits are available for installation-friendly and easy service applications. These 6HK kits may be used in multiple application for air handlers, modular blowers, and residential package units.

Blowers – All models use direct-drive, multi-speed PSC motors.

Blowers – MA series models to match any air flow (2 to 5 tons) or voltage requirement (115v, 230v, and 460v models are available). The compact size allows easy installation. Blowers are sized to deliver design air quantity both efficiently and quietly. The direct-drive, multi-speed blower motors provide a selection of air quantities to match any application. All models include a one-minute blower off delay as standard to enhance system efficiency ratings.

Cabinets – The durable, pre-painted steel protects the unit against rust and corrosion. All models have 1 inch foil face fiber glass insulation.

4HK Series Electric Heaters – Both single and three phase electric heater models are available to match any requirement. All heaters include nickel-chromium elements with a 5-year limited warranty on 1 ø heating elements and 1 year limited warranty on 3 ø heating elements. Sequencers are provided to control heaters in all models. Circuit breakers are used in 208/230 volt, single phase heaters of 13 KW and larger. Models equipped with circuit breakers may be altered in the field to use multi-source power supply. Over-temperature limit switches provide protection from airflow loss.

Limitations – These units must be wired and installed in accordance with all national and local safety codes.

Blowers – Models to match any air flow or voltage requirement. The compact size allows easy installation. Blowers are sized to deliver design air quantity both efficiently and quietly. The motors provide a selection of air quantities to match any application. All models include a one-minute blower off delay as standard to enhance system efficiency ratings.

Cabinets – The durable, pre-painted steel protects the unit against rust and corrosion. All models have 1 inch foil face fiber glass insulation.

Electric Heaters – Both single and three phase electric heater models are available to match any requirement. All heaters include nickel-chromium elements with a 5-year limited warranty on 1 ø heating elements and 1 year limited warranty on 3 ø heating elements. Sequencers are provided to control heaters in all models. Circuit breakers are used in 208/230 volt, single-phase heaters of 13 KW and larger.Models equipped with circuit breakers may be altered in the field to use multi-source power supply. Over-temperature limit switches provide protection from airflow loss.

Thermal Expansion Valve – Provides the ultimate refrigerant control required for today’s high efficient systems. The UPG bolt-on TXV provides easy installation to convert the air handler to the required refrigerant, which is a true bolt-on design that does not require brazing to replace or install.

Insulated Cabinet – All air handler cabinets are thermally insulated with 3/4″ foil faced insulation to prevent sweating.

Durable Finish Inside and Out – Air handler casings are made of pre-painted galvanized steel which provides a better paint to steel bond that resists corrosion and rust creep. All internal coil sheet metal parts are made of G60 galvanized or prepainted G30 galvainzed. All heaters include nickel-chromium elements with a 5-year limited warranty on 1 ø heating elements and 1 year limited warranty on 3 ø heating elements. Sequencers are provided to control heaters in all models. Circuit breakers are used in 208/230 volt, single-phase heaters of 13 KW and larger.Models equipped with circuit breakers may be altered in the field to use multi-source power supply. Over-temperature limit switches provide protection from airflow loss.

Filters – All models have internal filter racks provided for use with 1″ thick standard size filters.

Electric Heat Kits – The 6HK series of field installed electric heat kits are available for installation friendly and easy service applications. These 6 HK kits are available from 2 to 25 kW heat capacity.

Blowers – All models use 3-speed PSC motors to provide cooling SEER rating versatility.

RC2 – Rigid Case Construction interior endoskeleton provides structural support, flush sides, and locks in insulation.

Powder-Painted – G30 galvanized steel case provides a coated edge that resists corrosion and rust creep.

MaxAlloyTM Coil – Long life aluminum coils built to deliver lasting performance, efficiency and reliability.

Quality Construction – Structural components are made of Aluminum or G90 galvanized steel to prevent corrosion.

Improved Insulation Design – Single piece with no external screws to reduce thermal transmission paths to prevent sweating. Foil faced insulation for ease of cleaning.

Thermostatic Expansion Valve – Bolt-on TXV provides easy installation to convert the indoor coil to the required refrigerant and does not require brazing to replace or install. Select models are available with factory installed TXV.

Case Depth – These models have 20.5″ casing which provide ease of attic access and tight applications.

Thermoset Drain Pan – Positive slope for drainage to reduce cause for potential mold or contaminants.

Factory Sealed – Achieves 2% or less total airflow leakage rate at duct leakage test conditions in positive and negative pressure for system airflow verification.

Enhanced Filter Rack – All models have an internal filter rack for use with 1” thick standard size filters.

Electric Heat Kits – 6HK series of field installed electric heat kits are available for installation-friendly and easy service applications. These 6HK kits may be used in multiple application for air handlers, modular blowers, and residential package units.

High Efficiency Blowers – All models use high efficiency brushless DC motors to provide cooling SEER rating enhancement.

Thermal Expansion Valve – Provides the ultimate refrigerant control required for today’s high efficient systems. The UPG bolt-on TXV provides easy installation to convert the air handler to the required refrigerant, which is a true bolt-on design that does not require brazing to replace or install.

Insulated Cabinet – All air handler cabinets are thermally insulated with 3/4″ foil faced insulation to prevent sweating.

Durable Finish Inside and Out – Air handler casings are made of pre-painted galvanized steel which provides a better paint to steel bond that resists corrosion and rust creep. All internal coil sheet metal parts are made of G60 galvanized or prepainted G30 galvainzed. All heaters include nickel-chromium elements with a 5-year limited warranty on 1 ø heating elements and 1 year limited warranty on 3 ø heating elements. Sequencers are provided to control heaters in all models. Circuit breakers are used in 208/230 volt, single-phase heaters of 13 KW and larger.Models equipped with circuit breakers may be altered in the field to use multi-source power supply. Over-temperature limit switches provide protection from airflow loss.

Filters – All models have internal filter racks provided for use with 1″ thick standard size filters.

Electric Heat Kits – The 6HK series of field installed electric heat kits are available for installation friendly and easy service applications. These 6 HK kits are available from 2 to 25 kW heat capacity.

High Efficiency Blowers – All models use high efficiency brushless DC motors to provide cooling SEER rating enhancement.

Thermal Expansion Valve – Provides flexibility to use R-22 or R-410A refrigerant. A true bolt-on TXV, valve assembly and equalizer tube is available with no brazing required. TXV and sensing bulb are mounted inside the cased coil cabinet. (Must be field supplied for all “Flex-coils”).

Insulated Cabinet – All evaporator coil cabinets are thermally insulated with foil faced insulation to prevent sweating.

Internally Clean – All evaporator coils are factory leak-tested, dehydrated, sealed and shipped with a holding charge.

Durable Finish Inside and Out – Coil casings are made of pre-painted steel. The pre-treated flat galvanized steel provides a better paint to steel bond, which resist corrosion and rust creep. All internal metal parts are made of G90 pre-painted steel i.e. triangular plates, top plates, horizontal supports etc. (Coil header plates are non-painted due to the brazing process during production.).

Optimum Heat Transfer – Using the latest in heat transfer technology, staggered rows of copper tubes are mechanically expanded into aluminum fins to provide optimum air to surface contact for ample moisture removal as well as high performance ratings.

RC2 – Rigid Case Construction interior endoskeleton provides structural support, flush sides, and locks in insulation.

Powder-painted – G30 galvanized steel case provides a coated edge that resists corrosion and rust creep.

MaxAlloyTM Coil – Long life aluminum coils built to deliver lasting performance, efficiency and reliability.

Quality Construction – Structural components are made of Aluminum or G90 galvanized steel to prevent corrosion.

Improved Insulation Design – Single piece with no external screws to reduce thermal transmission paths to prevent sweating. Foil faced insulation for ease of cleaning.

Thermostatic Expansion Valve – Bolt-on TXV provides easy installation to convert the indoor coil to the required refrigerant and does not require brazing to replace or install. Select models are available with factory installed TXV.

Case Depth – These models have 20.5″ casing which provide ease of attic access and tight applications.

Thermoset Drain Pan – Positive slope for drainage to reduce cause for potential mold or contaminants.

Thermal Expansion Valve – Provides flexibility to use R-22 or R-410A refrigerant. A true bolt-on TXV, valve assembly and equalizer tube is available with no brazing required. TXV and sensing bulb are mounted inside the cased coil cabinet. (Must be field supplied for all “Flex-coils”).

Insulated Cabinet – All evaporator coil cabinets are thermally insulated with foil faced insulation to prevent sweating.

Internally Clean – All evaporator coils are factory leak-tested, dehydrated, sealed and shipped with a holding charge.

Durable Finish Inside and Out – Coil casings are made of pre-painted steel. The pre-treated flat galvanized steel provides a better paint to steel bond, which resist corrosion and rust creep. All internal metal parts are made of G90 pre-painted steel i.e. triangular plates, top plates, horizontal supports etc. (Coil header plates are non-painted due to the brazing process during production.).

Optimum Heat Transfer – Using the latest in heat transfer technology, staggered rows of copper tubes are mechanically expanded into aluminum fins to provide optimum air to surface contact for ample moisture removal as well as high performance ratings.

RC2 – Rigid Case Construction interior endoskeleton provides structural support, flush sides, and locks in insulation.

Powder-painted – G30 galvanized steel case provides a coated edge that resists corrosion and rust creep.

MaxAlloyTM Coil – Long life aluminum coils built to deliver lasting performance, efficiency and reliability.

Quality Construction – Structural components are made of Aluminum or G90 galvanized steel to prevent corrosion.

Improved Insulation Design – Single piece with no external screws to reduce thermal transmission paths to prevent sweating. Foil faced insulation for ease of cleaning.

Thermostatic Expansion Valve – Bolt-on TXV provides easy installation to convert the indoor coil to the required refrigerant and does not require brazing to replace or install. Select models are available with factory installed TXV.

Case Depth – These models have 20.5″ casing which provide ease of attic access and tight applications.

Thermoset Drain Pan – Positive slope for drainage to reduce cause for potential mold or contaminants.

Thermal Expansion Valve – Provides flexibility to use R-22 or R-410A refrigerant. A true bolt-on TXV, valve assembly and equalizer tube is available with no brazing required. TXV and sensing bulb are mounted inside the cased coil cabinet. (Must be field supplied for all “Flex-coils”).

Insulated Cabinet – All evaporator coil cabinets are thermally insulated with foil faced insulation to prevent sweating.

Internally Clean – All evaporator coils are factory leak-tested, dehydrated, sealed and shipped with a holding charge.

Durable Finish Inside and Out – Coil casings are made of pre-painted steel. The pre-treated flat galvanized steel provides a better paint to steel bond, which resist corrosion and rust creep. All internal metal parts are made of G90 pre-painted steel i.e. triangular plates, top plates, horizontal supports etc. (Coil header plates are non-painted due to the brazing process during production.).

Optimum Heat Transfer – Using the latest in heat transfer technology, staggered rows of copper tubes are mechanically expanded into aluminum fins to provide optimum air to surface contact for ample moisture removal as well as high performance ratings.