Wholesale Distributor to the HVAC/R Industry Since 1957

Fairfield, NJ  –  Middlesex, NJ  –  Mt. Laurel, NJ  –  Lakewood, NJ

DAILY DELIVERIES SERVING:  New Jersey  •  New York  •  Connecticut  •  Pennsylvania  •  Delaware
TELEPHONE: 1-800-458-7329

Fraser-Johnston
Heating & Air Conditioning Equipment



Luxaire

Fraser-Johnston Products

Luce, Schwab & Kase is a proud Fraser-Johnston distributor! Quality products are the foundation for a quality business. That's why Fraser-Johnston is committed to state-of-the-art design and manufacturing to make sure you get a full spectrum of reliable residential and light commercial products that are easy to install and simple to service.

Fraser-Johnston gives you multi-tier product offering – including affordable Climasure™, compact LX, and advanced Acclimate™ Series models.

Request a Fraser-Johnston Residential & Light Commercial HVAC Equipment Catalog



Gas Furnaces • Air Conditioners • Heat Pumps
Air Handlers • Evaporator Coils • Rooftops • Blowers

GAS FURNACES


Fraser-Johnston Climasure™-Series
80% AFUE Gas Furnace

Fraser-Johnston TG8S-Series 80 AFUE Furnace

  • Standard Efficiency (TG8S): 
    80.0% AFUE Single-Stage PSC Multi-Position NG33 Gas Furnaces (40,000 – 130,000 MBH)
  • Compact 33" Height and Standard Cabinet Widths.
  • Multi-Position Design With Minimal Conversion Requirements.
  • Airflow Leakage Rate of Less Than 1% of Total Airflow @ 1" ESP.
  • PSC Four-Speed Direct Drive Motor with Large, Quiet Blower.
  • Fully-Supported, Slide-Out Blower Assembly for Easy Service Access.
  • Tubular Aluminized Steel Primary Heat Exchanger.
  • High-Level Self-Diagnostic Controls With Fault Codes.
  • Sharp Edges Have Been Eliminated By Folding and Flattening the Sheet Metal.
  • Fully-Gasketed, Independent Access Doors With View Ports.
  • External Air Filters (Not Included) Provide Flexibility for IAQ Needs.
  • All Models Are Propane Convertible.

These compact units employ induced combustion, reliable hot surface ignition and high heat transfer aluminized tubular heat exchangers. The units are factory shipped for installation in upflow or horizontal applications and may be converted for downflow applications.

These furnaces are designed for residential installation in a basement, closet, alcove, attic, recreation room or garage and are also ideal for commercial applications. All units are factory assembled, wired and tested to assure safe dependable and economical installation and operation.

These units are Category I listed and may be common vented with another gas appliance as allowed by the National Fuel Gas Code.

Download Fraser-Johnston Climasure™-Series
80% AFUE Gas Furnace Literature




Fraser-Johnston LX-Series
80% AFUE Gas Furnace

Fraser-Johnston TM8X-Series 80 AFUE Furnace

  • Standard Efficiency (TM8X): 
    80% AFUE Single-Stage Multi-Position NG33 Gas Furnaces (60,000 – 120,000 MBH)
  • Easily applied in upflow, horizontal left or right, or downflow installation with minimal conversion necessary.
  • Compact, easy to install, ideal height 33" tall cabinet.
  • Blower-off delay for cooling SEER improvement.
  • Easy access to controls to connect power/control wiring.
  • Built-in, high level self diagnostics with fault code displays standard on integrated control module for reliable operation.
  • Low unit amp requirement for easy replacement application.
  • All models are convertable to use propane (LP) gas.
  • Electronic Hot Surface Ignition saves fuel cost with increased dependability and reliability.
  • 100% shut off main gas valve for extra safety.
  • 5 speed direct drive, X13 style high efficiency DC motor.
  • 24V, 40 VA control transformer and blower relay supplied for add-on cooling.
  • Hi-tech tubular aluminized steel primary heat exchanger.
  • Timed on, adjustable off blower capability for maximum comfort.
  • Blower door safety switch.
  • Solid removable bottom panel allows easy conversion.
  • Low NOx models have been designed to meet specific code requirements.
  • Airflow leakage less than 1% of total airflow at ductblaster conditions.
  • No knockouts to deal with, making installation easier.
  • Movable duct connector flanges for application flexibility.
  • Quiet inducer operation.
  • Inducer rotates for easy conversion of venting options.
  • Fully supported blower assembly for easy access and removal of blower.
  • External air filters used for maximum flexibility in meeting customers IAQ needs.
  • Venting applications - may be installed as a common vent with other gas-fired appliances or use a masonry chimney.
  • 1/4 turn knobs provided for easy door removal.
  • High-efficiency blower motor for lower electrical power usage and improved A/C SEER ratings.
  • Insulated blower compartment for thermal and acoustic performance.

These compact units employ induced combustion, reliable hot surface ignition and high heat transfer aluminized tubular heat exchangers. The units are factory shipped for installation in upflow or horizontal applications and may be converted for downflow applications.

These furnaces are designed for residential installation in a basement, closet, alcove, attic, recreation room or garage and are also ideal for commercial applications. All units are factory assembled, wired and tested to assure safe dependable and economical installation and operation.

These units are Category I listed and may be common vented with another gas appliance as allowed by the National Fuel Gas Code.

Download Fraser-Johnston LX-Series
80% AFUE Gas Furnace Literature




Fraser-Johnston LX-Series
80% AFUE Two-Stage Gas Furnace

Fraser-Johnston TM8V-Series 80% AFUE Furnace

  • Standard Efficiency (TM8V): 
    80% AFUE Two-Stage ECM NG33 Gas Furnaces (60,000 – 120,000 MBH)
  • Easily applied in upflow, horizontal left or right, or downflow installation with minimal conversion necessary.
  • Compact, easy to install, ideal height 33" tall cabinet.
  • Blower-off delay for cooling SEER improvement.
  • Easy access to controls to connect power/control wiring.
  • Built-in, high level self diagnostics with fault code displays standard on integrated control module for reliable operation.
  • Low unit amp requirement for easy replacement application.
  • All models are convertable to use propane (LP) gas.
  • Electronic Hot Surface Ignition saves fuel cost with increased dependability and reliability.
  • 100% shut off main gas valve for extra safety.
  • 5 speed direct drive, X13 style high efficiency DC motor.
  • 24V, 40 VA control transformer and blower relay supplied for add-on cooling.
  • Hi-tech tubular aluminized steel primary heat exchanger.
  • Timed on, adjustable off blower capability for maximum comfort.
  • Blower door safety switch.
  • Solid removable bottom panel allows easy conversion.
  • Low NOx models have been designed to meet specific code requirements.
  • Airflow leakage less than 1% of total airflow at ductblaster conditions.
  • No knockouts to deal with, making installation easier.
  • Movable duct connector flanges for application flexibility.
  • Quiet inducer operation.
  • Inducer rotates for easy conversion of venting options.
  • Fully supported blower assembly for easy access and removal of blower.
  • External air filters used for maximum flexibility in meeting customers IAQ needs.
  • Venting applications - may be installed as a common vent with other gas-fired appliances or use a masonry chimney.
  • 1/4 turn knobs provided for easy door removal.
  • High-efficiency blower motor for lower electrical power usage and improved A/C SEER ratings.
  • Insulated blower compartment for thermal and acoustic performance.

These compact units employ induced combustion, reliable hot surface ignition and high heat transfer aluminized tubular heat exchangers. The units are factory shipped for installation in upflow or horizontal applications and may be converted for downflow applications.

These furnaces are designed for residential installation in a basement, closet, alcove, attic, recreation room or garage and are also ideal for commercial applications. All units are factory assembled, wired and tested to assure safe dependable and economical installation and operation.

These units are Category I listed and may be common vented with another gas appliance as allowed by the National Fuel Gas Code.

Download Fraser-Johnston LX-Series
80% AFUE Two-Stage Gas Furnace Literature




Fraser-Johnston
78% AFUE Commercial Gas Furnace

Fraser-Johnston GY8S-E-Series Commercial 78% AFUE Furnace

  • Mid-High Efficiency (GY8S-E): 
    78% AFUE Commercial Belt Drive Furnace (160,000 MBH)
  • Easily applied in upflow, horizontal left or horizontal right installation with no conversion necessary.
  • Electronic hot surface ignition with high reliability and dependability.
  • 100% shut off main gas valve for added safety.
  • Rollout safety control.
  • Large belt drive blower for high CFM and static capability.
  • 1-1/2 HP ball bearing motor.
  • Reliable hot surface ignitor.
  • Aluminized tubular heat exchanger for long term durability.
  • High quality inducer motor for quiet operation.
  • Standard terminals for controlling humidifiers and EAC's or other commercial application requirements.
  • 40 VA control transformer fuse protected.
  • Easy to connect power and control wiring.
  • Efficiency ratings of 78 AFUE attained by using tubular heat exchangers.
  • Cooling relay supplied for easy installation of add-on cooling.
  • Adjustable fan-off settings to eliminate "cold-blow".
  • Equipped with timer relay providing motor protection if operated on continuous blower or if units are "twinned".
  • 208/230v operation, convertible for 115v.
  • Model is propane convertible.
  • Attractive baked enamel finish for durability.

This mid-high efficiency, compact unit employs induced combustion, reliable hot surface ignition and high heat transfer tubular heat exchangers. The unit is factory shipped for installation in upflow or horizontal applications.

This furnace is designed for residential and commercial applications. The unit is factory assembled, wired and tested to assure safe, dependable and economical installation and operation.

These units are Category I listed and may be common vented with another gas appliance as allowed by the National Fuel Gas Code.



Fraser-Johnston Climasure™-Series
95.5% AFUE Gas Furnace

Fraser-Johnston TG9S-Series 95.5% AFUE Furnace

  • High Efficiency (TG9S): 
    95.5% AFUE Single-Stage PSC Multi-Position NG33 Gas Furnaces (40,000 – 130,000 MBH)

Energy Star Certified
  • Compact 33" Height and Standard Cabinet Widths.
  • Multi-Position Design With Minimal Conversion Requirements.
  • Airflow Leakage Rate of Less Than 1% of Total Airflow @ 1" ESP.
  • PSC Four-Speed Direct Drive Motor with Large, Quiet Blower.
  • Fully-Supported, Slide-Out Blower Assembly for Easy Service Access.
  • Tubular Aluminized Steel Primary Heat Exchanger.
  • High-Level Self-Diagnostic Controls With Fault Codes.
  • Sharp Edges Have Been Eliminated By Folding and Flattening the Sheet Metal.
  • Fully-Gasketed, Independent Access Doors With View Ports.
  • External Air Filters (Not Included) Provide Flexibility for IAQ Needs.
  • All Models Are Propane Convertible.
  • Energy Star certified.

These compact units employ induced combustion, reliable hot surface ignition and high heat transfer aluminized tubular heat exchangers. The units are factory shipped for installation in upflow or horizontal applications and may be converted for downflow applications.

These furnaces are designed for residential installation in a basement, closet, alcove, attic, recreation room or garage and are also ideal for commercial applications. All units are factory assembled, wired and tested to assure safe dependable and economical installation and operation.

Download Fraser-Johnston Climasure™-Series
95.5% AFUE Gas Furnace Literature




Fraser-Johnston
95.0% AFUE Gas Furnace

Fraser-Johnston 95.0% AFUE Single Stage ECM Multi-Position Gas Furnace

  • High Efficiency (TM9E): 
    95.0% AFUE Single Stage ECM Multi-Position Gas Furnace (60,000 – 120,000 MBH)
New

  • Easily applied in upflow, horizontal left or right, or downflow installation with minimal conversion necessary.
  • Compact, easy to install, ideal height 33" tall cabinet.
  • Blower-off delay for cooling SEER improvement.
  • Easy access to controls to connect power/control wiring.
  • Built-in, high level self diagnostics with fault code displays standard on integrated control module for reliable operation.
  • Low unit amp requirement for easy replacement application.
  • All models are convertable to use propane (LP) gas.
  • Electronic Hot Surface Ignition saves fuel cost with increased dependability and reliability.
  • 100% shut off main gas valve for extra safety.
  • 5-speed, direct drive Standard ECM style high efficiency DC motor.
  • 24V, 40 VA control transformer and blower relay supplied for add-on cooling.
  • Hi-tech tubular aluminized steel primary heat exchanger.
  • Secondary heat exchanger made of corrosion resistant stainless steel materials.
  • Timed on, adjustable off blower capability for maximum comfort. Blower door safety switch.
  • Solid removable bottom panel allows easy conversion.
  • Airflow leakage less than 1% of nominal airflow at ductblaster conditions.
  • No knockouts to deal with, making installation easier.
  • Movable duct connector flanges for application flexibility.
  • Quiet inducer operation.
  • Inducer rotates for easy conversion of venting options.
  • Fully supported blower assembly for easy access and removal of blower.
  • External air filters used for maximum flexibility in meeting customers IAQ needs.
  • Protection included from air intake, exhaust vent, or condensate blockage.
  • Patent pending self priming internal condensate trap design for easy installation.
  • Venting applications – may be installed as a either 2-pipe (sealed combustion) or single-pipe vent (using indoor combustion air.
  • No special vent termination required.
  • 1/4 turn knobs provided for easy door removal.
  • High-efficiency blower motor for lower electrical power usage and improved A/C SEER ratings.
  • Insulated blower compartment for terminal and acoustic performance.

These compact units employ induced combustion, reliable hot surface ignition and high heat transferaluminized tubular heat exchangers. The units are factory shipped for installation in upflow or horizontal applications and may be converted for downflow applications.

These furnaces are designed for residential installation in a basement, closet, alcove, attic, recreation room or garage and are also ideal for commercial applications. All units are factory assembled, wired and tested to assure safe dependable and economical installation and operation.

These units are Category IV listed and may be vented either through side wall or roof applications using approved plastic combustion air and vent piping.



Fraser-Johnston LX-Series
95.5% AFUE Gas Furnace

Fraser-Johnston TM9X-Series 95.5% AFUE Furnace

  • High Efficiency (TM9X): 
    95.5% AFUE Single Stage Multi-Position NG33 X13 Gas Furnaces (60,000 – 120,000 MBH)

Energy Star Certified
  • Easily applied in upflow, horizontal left or right, or downflow installation with minimal conversion necessary.
  • Compact, easy to install, ideal height 33" tall cabinet.
  • Blower-off delay for cooling SEER improvement.
  • Easy access to controls to connect power/control wiring.
  • Built-in, high level self diagnostics with fault code displays standard on integrated control module for reliable operation.
  • Low unit amp requirement for easy replacement application.
  • All models are convertable to use propane (LP) gas.
  • Electronic Hot Surface Ignition saves fuel cost with increased dependability and reliability.
  • 100% shut off main gas valve for extra safety.
  • 5 speed direct drive, X13 style high efficiency DC motor.
  • 24V, 40 VA control transformer and blower relay supplied for add-on cooling.
  • Hi-tech tubular aluminized steel primary heat exchanger.
  • Timed on, adjustable off blower capability for maximum comfort.
  • Blower door safety switch.
  • Solid removable bottom panel allows easy conversion.
  • Low NOx models have been designed to meet specific code requirements.
  • Airflow leakage less than 1% of total airflow at ductblaster conditions.
  • No knockouts to deal with, making installation easier.
  • Movable duct connector flanges for application flexibility.
  • Quiet inducer operation.
  • Inducer rotates for easy conversion of venting options.
  • Fully supported blower assembly for easy access and removal of blower.
  • External air filters used for maximum flexibility in meeting customers IAQ needs.
  • Venting applications - may be installed as a common vent with other gas-fired appliances or use a masonry chimney.
  • 1/4 turn knobs provided for easy door removal.
  • High-efficiency blower motor for lower electrical power usage and improved A/C SEER ratings.
  • Insulated blower compartment for thermal and acoustic performance.
  • Energy Star certified.

These compact units employ induced combustion, reliable hot surface ignition and high heat transfer aluminized tubular heat exchangers. The units are factory shipped for installation in upflow or horizontal applications and may be converted for downflow applications.

These furnaces are designed for residential installation in a basement, closet, alcove, attic, recreation room or garage and are also ideal for commercial applications. All units are factory assembled, wired and tested to assure safe dependable and economical installation and operation.

These units are Category IV listed and may be vented either through side wall or roof applications using approved plastic combustion air and venr piping.

Download Fraser-Johnston LX-Series
80% AFUE Gas Furnace Literature




Fraser-Johnston LX-Series
96% AFUE Two-Stage Gas Furnace

Fraser-Johnston TM9V-Series 96% AFUE Furnace

  • High Efficiency (TM9V): 
    96% AFUE 2-Stage Variable Speed Multi-Position Gas Furnaces (40,000 – 120,000 MBH)

Energy Star Certified
  • Two stage heating operation includes two stage gas valve, two stage inducer operation and variable speed ECM blower operation. Adjustable delay timer allows two stage operation with a single stage thermostat.
  • Easily applied in upflow, horizontal left or right, or downflow installation with minimal conversion necessary.
  • Compact, easy to install, ideal height 33" tall cabinet.
  • ECM variable speed drive for cooling SEER enhancement, improved comfort with optional airflow delay profiles, and continuous fan options for IAQ performance.
  • Easy access to controls to connect power/control wiring.
  • Built-in, high level self diagnostics with fault code display.
  • Low unit amp requirement for easy replacement application.
  • All models are convertable to use propane (LP) gas.
  • Electronic Hot Surface Ignition saves fuel cost with increased dependability and reliability.
  • 100% shut off main gas valve for extra safety.
  • 24V, 40 VA control transformer and blower relay supplied for add-on cooling.
  • Hi-tech tubular aluminized steel primary heat exchanger with stainless steel tube/aluminum fin secondary heat exchanger for outstanding efficiency. Solid removable bottom panel allows easy conversion.
  • Movable duct connector flanges for application flexibility.
  • Quiet inducer operation, burner, and blower operation.
  • Inducer rotates for easy conversion of venting options.
  • Airflow leakage less than 1% of total airflow at ductblaster conditions.
  • No knockouts to deal with, making installation easier.
  • Movable duct connector flanges for application flexibility.
  • Fully supported blower assembly for easy access and removal of blower.
  • External air filters used for maximum flexibility in meeting customers IAQ needs.
  • Venting applications - may be installed as a common vent with other gas-fired appliances or use a masonry chimney.
  • 1/4 turn knobs provided for easy door removal.
  • Protection included from air intake, exhaust vent or condensate blockage.
  • Insulated blower compartment for thermal and acoustic performance.
  • Venting applications maybe installed as either 2-pipe sealed combustion or single pipe vent using indoor combustion air.
  • Energy Star certified.

These compact units employ induced combustion, reliable hot surface ignition and high heat transfer aluminized tubular heat exchangers. The units are factory shipped for installation in upflow or horizontal applications and may be converted for downflow application.

These furnaces are designed for residential installation in a basement, closet, alcove, attic, recreation room or garage and are also ideal for commercial applications. All units are factory assembled, wired and tested to assure safe dependable and economical installation and operation.

These units are Category IV listed and may be vented either through side wall or roof applications using approved plastic combustion air and venr piping.

Download Fraser-Johnston LX-Series
96% AFUE Two-Stage Gas Furnace Literature




Fraser-Johnston TP9C-Series
97.7% AFUE Gas Furnace


Fraser-Johnston TP9C-Series 97.7% AFUE Furnace

  • High Efficiency (TP9C): 
    95.5% AFUE Modulating VS ECM Multi-Position Gas Furnaces (60,000 – 120,000 MBH)

Energy Star Certified
  • Compact 33" Height and Standard Cabinet Widths.
  • 100 Stage Modulating VS ECM Design.
  • Communiciations Capable control system.
  • Multi-Position Design With Minimal Conversion Requirements.
  • Airflow Leakage Rate of Less Than 1% of Total Airflow @ 1" ESP.
  • ECM Variable-Speed Motor with Large, Quiet Blower.
  • Fully-Supported, Slide-Out Blower Assembly for Easy Service Access.
  • High-Level Self-Diagnostic Controls With Fault Codes.
  • Fully-Gasketed, Independent Access Doors With View Ports, Retail Appearance.
  • External Air Filters (Not Included) Provide Flexibility for IAQ Needs.
  • Sharp Edges Eliminated By Folding and Flattening the Sheet Metal.
  • Patent-Pending Condensate Management System Eliminates the Need for External Condensate Traps.
  • Energy Star certified.
NEW!

These TP9C furnaces are compact units that employ induced combustion, reliable hot surface ignition and high heat transfer aluminized tubular heat exchangers. The units are factory shipped for installation in upflow or horizontal applications and may be converted for downflow applications.

These furnaces are designed for residential installation in a basement, closet, alcove, attic, recreation room or garage and are also ideal for commercial applications. All units are factory assembled, wired and tested to assure safe dependable and economical installation and operation.

Designed and certified as Category IV furnaces, these CP9C models may be installed as direct vent systems through side wall or roof applications using approved plastic combustion air and vent materials.

Download Fraser-Johnston TP9C-Series
97.7% AFUE Gas Furnace Literature



AIR CONDITIONERS


Fraser-Johnston LX™-Series
13-SEER Air Conditioners

Fraser-Johnston TC3-Series 13-SEER air conditioners

  • TC3-Series: 
    13-SEER R410A single-phase air conditioners
    (1-1/2 – 5 tons)
  •  
  • Supercedes TCJD-Series
New

  • Small Footprint – Minimum footprint for easier handling, transportation, and installation.
  • Easier Installation – Independent panels provide quick access for unit setup. Installation time is reduced by easy power and control wiring access. Options are provided for indoor piston or TXV. The factory installed filter-drier and factory charge for a 15-ft. lineset means less time spent brazing and charging the system. The small base dimension and reduced unit clearances make for easier retrofits.
  • Accessible Information – QR code on unit provides quick access to technical documents and warranty information.
  • Durable Finish – The coated steel wire fan guard, coated external fasteners, and pre-treated G90-equivalent galvanized steel chassis components resist corrosion and rust creep. Titanium colored powdercoat paint further protects external panels.
  • Quality Coils – The high efficiency microchannel aluminum coil is manufactured using an improved material system providing reliable performance and small unit size.
  • Reliable Operation – Ball bearing fan motors provide superior performance in extreme temperatures.
  • Rugged Coil Protection – Coils are protected from mechanical damage by a proven stamped steel coil guard design.
  • Protected Compressor – Compressors are protected internally by a high pressure relief valve and a temperature sensor, and externally by the system high pressure switch. The liquid line filter-drier is factory installed to protect the compressor against moisture and debris.
  • Environmentally Friendly – CFC-free R-410A refrigerant delivers environmentally friendly performance with zero ozone depletion.
  • Top Discharge – Warm air is blown up, away from the structure and any landscaping and allows compact location on multi-unit applications.
  • Low Operating Sound Levels – Developed using CFD and FEA tools, the sturdy cabinet and top design provides sound performance of 76 dBA or lower. Compatible accessories for further sound reduction are also available.
  • Better Service Access – Diagonal base valves with open access for low-loss fittings, single panel access to the electrical controls, swing out control box for full corner access, and removable fan guard allow easy access for unit maintenance.
  • Agency Listed – Safety certified by CSA to UL 1995/CSA 22.2. Performance certified to ANSI/AHRI Standard 210/240 in accordance with the Unitary Small Equipment certification program.

The TC3 models are the latest iteration in our successful LX Series split system air conditioner lineup. Optimized for the 13 SEER Regional Minimum Efficiency in the North US and Canada, these outdoor units are specifically designed to be matched with Fraser-Johnston indoor coils, furnaces, and air handlers to provide a complete system solution.

Download Fraser-Johnston TC3-Series
13-SEER Air Conditioner Literature




Fraser-Johnston LX-Series
13-SEER Air Conditioners

Fraser-Johnston TCJD-Series 13-SEER air conditioners

  • TCJD-Series: 
    13-SEER R410A single-phase air conditioners
    (1-1/2 – 5 tons)
  •  
  • Superceded by TC3-Series

  • Small Footprint – extremely lightweight with a compact footprint, it will be a perfect fit for any application.
  • Quality Condenser Coils – The coil is constructed of aluminum microchannel tubing and enhanced aluminum fins for increased efficiency.
  • Coil Protection – Coils are protected from damage by a polymer mesh applied between the coil face, and a coated steel coil guard.
  • Protected Compressor – Compressors are internally protected against high pressure and temperature. This is accomplished by the simultaneous operation of high pressure relief valve and a temperature sensor which protects the compressor if undesirable operating conditions occur. A liquid line filter-drier further protects the compressor.
  • Durable Finish – The cabinet is made of pre-painted steel. The pre-treated flat galvanized steel provides a better paint-to-steel bond, which resists corrosion and rust creep. Special primer formulas and matted champagne finish insure less fading when exposed to sunlight.
  • Lower Installed Cost – Installation time and costs are reduced by easy power and control wiring connections. The small base dimension means less space is required on the ground or roof.
  • Top Discharge – The warm air from the top mounted fan is blown away from the structure and any landscaping. This allows compact location on multi-unit applications.
  • Low Operating Sound Level – The upward air flow carries the normal operating noise away from the living area. The rigid top panel effectively isolates any motor sound. Isolator mounted compressor and the condenser coil muffle the normal fan motor and compressor operating sounds.
  • Low Maintenance – Long life permanently lubricated motor-bearings need no annual servicing.
  • Easy Service Access – Fully exposed refrigerant connections and a single panel covering the electrical controls make for easy servicing of the unit.
  • Secured Service Valves – Secured re-usable service valves are provided on both the liquid and vapor sweat connections for ease of evacuating and charging.
  • U.L. and C.U.L Listed – Approved for outdoor application. Certified in accordance with the Unitary Small Equipment certification program, which is based on ARI Standard 210/240.

The 13 SEER Series Mid-Tier Series condensing unit is the outdoor part of a versatile system of air conditioning. It is designed to be custom matches with one of UPG's complete line of evaporator sections, each designed to serve a specific function.

Download Fraser-Johnston LX-Series
13-SEER Air Conditioner Literature




Fraser-Johnston LX-Series
13-SEER 3-Phase Air Conditioners

Fraser-Johnston TCJD-Series 13-SEER 3-Phase air conditioners

  • TCJD-Series: 
    13-SEER R410A 3-phase air conditioners
    (2-1/2 – 5 tons)

  • Small Footprint – extremely lightweight with a compact footprint, it will be a perfect fit for any application.
  • Quality Condenser Coils – The coil is constructed of aluminum microchannel tubing and enhanced aluminum fins for increased efficiency.
  • Coil Protection – Coils are protected from damage by a polymer mesh applied between the coil face, and a coated steel coil guard.
  • Protected Compressor – Compressors are internally protected against high pressure and temperature. This is accomplished by the simultaneous operation of high pressure relief valve and a temperature sensor which protects the compressor if undesirable operating conditions occur. A liquid line filter-drier further protects the compressor.
  • Durable Finish – The cabinet is made of pre-painted steel. The pre-treated flat galvanized steel provides a better paint-to-steel bond, which resists corrosion and rust creep. Special primer formulas and matted champagne finish insure less fading when exposed to sunlight.
  • Lower Installed Cost – Installation time and costs are reduced by easy power and control wiring connections. The small base dimension means less space is required on the ground or roof.
  • Top Discharge – The warm air from the top mounted fan is blown away from the structure and any landscaping. This allows compact location on multi-unit applications.
  • Low Operating Sound Level – The upward air flow carries the normal operating noise away from the living area. The rigid top panel effectively isolates any motor sound. Isolator mounted compressor and the condenser coil muffle the normal fan motor and compressor operating sounds.
  • Low Maintenance – Long life permanently lubricated motor-bearings need no annual servicing.
  • Easy Service Access – Fully exposed refrigerant connections and a single panel covering the electrical controls make for easy servicing of the unit.
  • Secured Service Valves – Secured re-usable service valves are provided on both the liquid and vapor sweat connections for ease of evacuating and charging.
  • U.L. and C.U.L Listed – Approved for outdoor application. Certified in accordance with the Unitary Small Equipment certification program, which is based on ARI Standard 210/240.

The 13 SEER Series Mid-Tier Series condensing unit is the outdoor part of a versatile system of air conditioning. It is designed to be custom matches with one of UPG's complete line of evaporator sections, each designed to serve a specific function.

Download Fraser-Johnston LX-Series
13-SEER 3-Phase Air Conditioner Literature




Fraser-Johnston LX-Series
14.5-SEER Air Conditioners

Fraser-Johnston TF4-Series 14.5-SEER air conditioners

  • TF4-Series: 
    14.5-SEER R410A single-phase air conditioners
    (1-1/2 – 5 tons)
  •  
  • Supercedes TCJF-series
  • New

Energy Star Certified
  • Quality Coils – Enhanced aluminum fins are mechanically bonded to copper tubing.
  • Scroll Compressor – Featuring the newest generation of high efficiency scroll compressors.
  • Copper filter-drier – The factory installed filter drier features copper construction for reliable long term protection.
  • Easier Installation – Independent panels provide quick access for unit setup. Installation time is reduced by easy power and control wiring access. Select indoor matches with factory-mounted TXVs are available for quicker system installation. The factory installed filter-drier and factory charge for a 15-ft. lineset means less time spent brazing and charging the system. The small base dimension and reduced unit clearances make for easier retrofits.
  • Accessible Information – QR code on unit provides quick access to technical documents and warranty information. Durable Finish - The coated steel wire fan guard, coated external fasteners, and pre-treated G90-equivalent galvanized steel chassis components resist corrosion and rust creep. Titanium colored powdercoat paint further protects external panels.
  • Rugged Coil Protection – Coils are protected from mechanical damage by a proven stamped steel coil guard design.
  • Protected Compressor – Compressors are protected internally by a high pressure relief valve and a temperature sensor, and externally by the system high pressure switch. The liquid line filter-drier is factory installed to protect the compressor against moisture and debris.
  • Reliable Operation – Ball bearing fan motors provide superior performance in extreme temperatures. Environmentally Friendly - CFC-free R-410A refrigerant delivers environmentally friendly performance with zero ozone depletion.
  • Top Discharge – Warm air is blown up, away from the structure and any landscaping and allows compact location on multi-unit applications.
  • Low Operating Sound Levels – Developed using CFD and FEA tools, the sturdy cabinet and top design provides sound performance of 76 dBA or lower. Compatible accessories for further sound reduction are also available.
  • Better Service Access – Diagonal base valves with open access for low-loss fittings, single panel access to the electrical controls, swing out control box for full corner access, and removable fan guard allow easy access for unit maintenance.
  • Agency Listed – Approved for outdoor application. Certified in accordance with the Unitary Small Equipment certification program, which is based on ARI Standard 210/240.
  • Energy Star Certified.

The TF4 models are a new offering in our successful LX Series split system air conditioner lineup. These units are optimized for the new 14 SEER Regional Minimum Efficiency in the Southeast US, and feature a tube-in-fin condenser coil, scroll compressor, and copper filter-drier. These outdoor units have been specifically designed to be matched with Fraser-Johnston indoor coils, furnaces, and air handlers to provide a complete system solution.

Download Fraser-Johnston TF4-series
14.5-SEER Air Conditioner Literature




Fraser-Johnston LX-Series
14.5-SEER Air Conditioners

Fraser-Johnston TCJF-Series 14.5-SEER air conditioners

  • TCJF-Series: 
    14.5-SEER R410A single-phase air conditioners
    (1-1/2 – 5 tons)
  •  
  • Superceded by TF4-series

Energy Star Certified
  • Small Footprint – extremely lightweight with a compact footprint, it will be a perfect fit for any application.
  • Quality Condenser Coils – The coil is constructed of aluminum microchannel tubing and enhanced aluminum fins for increased efficiency.
  • Coil Protection – Coils are protected from damage by a polymer mesh applied between the coil face, and a coated steel coil guard.
  • Protected Compressor – Compressors are internally protected against high pressure and temperature. This is accomplished by the simultaneous operation of high pressure relief valve and a temperature sensor which protects the compressor if undesirable operating conditions occur. A liquid line filter-drier further protects the compressor.
  • Durable Finish – The cabinet is made of pre-painted steel. The pre-treated flat galvanized steel provides a better paint-to-steel bond, which resists corrosion and rust creep. Special primer formulas and matted champagne finish insure less fading when exposed to sunlight.
  • Lower Installed Cost – Installation time and costs are reduced by easy power and control wiring connections. The small base dimension means less space is required on the ground or roof.
  • Top Discharge – The warm air from the top mounted fan is blown away from the structure and any landscaping. This allows compact location on multi-unit applications.
  • Low Operating Sound Level – The upward air flow carries the normal operating noise away from the living area. The rigid top panel effectively isolates any motor sound. Isolator mounted compressor and the condenser coil muffle the normal fan motor and compressor operating sounds.
  • Low Maintenance – Long life permanently lubricated motor-bearings need no annual servicing.
  • Easy Service Access – Fully exposed refrigerant connections and a single panel covering the electrical controls make for easy servicing of the unit.
  • Secured Service Valves – Secured re-usable service valves are provided on both the liquid and vapor sweat connections for ease of evacuating and charging.
  • U.L. and C.U.L Listed – Approved for outdoor application. Certified in accordance with the Unitary Small Equipment certification program, which is based on ARI Standard 210/240.
  • Energy Star Certified.

The 14.5 SEER Series Mid-Tier Series condensing unit is the outdoor part of a versatile system of air conditioning. It is designed to be custom matches with one of UPG's complete line of evaporator sections, each designed to serve a specific function.

Download Fraser-Johnston LX-Series
14.5-SEER Air Conditioner Literature




Fraser-Johnston TCHD-Series
13-SEER Air Conditioners

Fraser-Johnston TCHD-Series 13-SEER air conditioners

  • TCHD-Series: 
    13-SEER R410A Horizontal Discharge Split-System Air Conditioners
    (1-1/2 – 5 tons)

  • Performance – Efficiency levels from 13.0 SEER/11.0 EER with a loose coil up to 16.0 SEER/14.0 EER (some models) when coupled with an ECM indoor blower.
  • Small Footprint – Compact "slim-line" design allows for easy installation in tight spaces. Units can be stacked two-high with approved stacking kit.
  • Sound Reducing System – The combination of a swept-wing fan, rigid base pan, isolated compressor compartment, and quiet scroll compressor reduce sound to as low as 67 dBA.
  • Low Operating Sound Levels – The swept-wing condenser fan in blow-through configuration provides for whisper-quiet operation by allowing air to flow smoothly and efficiently across the fan tips.
  • Quality Condenser Coils – The coil is constructed of aluminum microchannel tubing and enhanced aluminum fins for compact size and increased efficiency.
  • Environmentally Friendly Refrigerant – The next generation refrigerant R-410A delivers environmentally friendly performance with zero ozone depletion.
  • Durable Cabinet – Heavy-gage steel cabinet and tubular base rails provide added support.
  • Aesthetic – Powder paint "Champagne" color provides an attractive retail finish.
  • Agency Listed – Safety certified by CSA to UL 1995/CSA 22.2. Performance certified to ANSI/AHRI Standard 210/240 in accordance with the Unitary Small Equipment certification program.

The Premium Series TCHD models are the outdoor part of a versatile air conditioning system. These condensing units are ideal for virtually every residential or commercial application where space is limited, aesthetics is a necessity, sound ordinances and proximity to neighbors demand ultra-quiet operation, peak performance season after season is ensured.

These remarkably compact units requires minimal service and airflow clearances, allowing them to be positioned as close as six inches (6") from an obstruction. This design allows the unit to be located virtually anywhere – on the ground, roof, balcony, under a deck, or mounted to an outside wall. When installation footprint is limited, these units can be stacked two-high using the approved stacking kit. Most models offer combinations that achieve Energy Star® efficiency levels.

Download Fraser-Johnston TCHD-Series
13-SEER Air Conditioner Literature




Fraser-Johnston TCHD-Series
13-SEER 3-Phase Air Conditioners

Fraser-Johnston TCHD-Series 13-SEER 3-Phase air conditioners

  • TCHD-Series: 
    13-SEER 3-Phase R410A Horizontal Discharge Split-System Air Conditioners
    (2-1/2 – 5 tons)

  • Performance – Efficiency levels from 13.0 SEER/11.0 EER with a loose coil up to 16.0 SEER/14.0 EER (some models) when coupled with an ECM indoor blower.
  • Small Footprint – Compact "slim-line" design allows for easy installation in tight spaces. Units can be stacked two-high with approved stacking kit.
  • Sound Reducing System – The combination of a swept-wing fan, rigid base pan, isolated compressor compartment, and quiet scroll compressor reduce sound to as low as 67 dBA.
  • Low Operating Sound Levels – The swept-wing condenser fan in blow-through configuration provides for whisper-quiet operation by allowing air to flow smoothly and efficiently across the fan tips.
  • Quality Condenser Coils – The coil is constructed of aluminum microchannel tubing and enhanced aluminum fins for compact size and increased efficiency.
  • Environmentally Friendly Refrigerant – The next generation refrigerant R-410A delivers environmentally friendly performance with zero ozone depletion.
  • Durable Cabinet – Heavy-gage steel cabinet and tubular base rails provide added support.
  • Aesthetic – Powder paint "Champagne" color provides an attractive retail finish.
  • Agency Listed – Safety certified by CSA to UL 1995/CSA 22.2. Performance certified to ANSI/AHRI Standard 210/240 in accordance with the Unitary Small Equipment certification program.

The Premium Series TCHD models are the outdoor part of a versatile air conditioning system. These condensing units are ideal for virtually every residential or commercial application where space is limited, aesthetics is a necessity, sound ordinances and proximity to neighbors demand ultra-quiet operation, peak performance season after season is ensured.

These remarkably compact units requires minimal service and airflow clearances, allowing them to be positioned as close as six inches (6") from an obstruction. This design allows the unit to be located virtually anywhere – on the ground, roof, balcony, under a deck, or mounted to an outside wall. When installation footprint is limited, these units can be stacked two-high using the approved stacking kit. Most models offer combinations that achieve Energy Star® efficiency levels.

Download Fraser-Johnston TCHD-Series
13-SEER 3-Phase Air Conditioner Literature




Fraser-Johnston Acclimate™
16-SEER Air Conditioners

Fraser-Johnston AL6B-Series 16-SEER air conditioners

  • AL6B-Series: 
    Premium 16-SEER R410A Split-System Air Conditioners
    (2 – 5 tons)

Energy Star Certified
  • Superior Coil Protection – A stamped, decorative metal coil guard completely protects the coil from debris and other damaging material.
  • Protected Compressor – The compressor is safeguarded against abnormal pressures and temperatures by an internal pressure relief valve, an internal temperature sensor, and factory high and low pressure system controls. A factory installed liquid line filter-drier further protects the compressor against moisture and debris.
  • Environmentally Friendly Refrigerant – The next generation refrigerant R-410A delivers environmentally friendly performance with zero ozone depletion.
  • Durable Finish – An automotive quality finish provides the ultimate protection from harmful UV rays and rust creep, ensuring a long-lasting, high quality appearance. A powder-paint topcoat is applied over a baked-on primer using a galvanized, zinc coated steel base material. The result is a finish that has been proven in testing to provide 33% greater durability than conventional powder-coat finishes.
  • Sound Reducing System – Features combination of swept-wing fan, composite base pan, isolated compressor compartment, and single-stage compressor to reduce overall sound to a mere whisper.
  • Low RPM Fan Motor – Helps to reduce airflow noise.
  • Swept Wing Fan – A fan design boasting technology adapted from aeronautic and defense engineering provides for whisper-quiet operation by allowing air to flow smoothly and efficiently across the fan tips.
  • Composite Base Pan – The strong and durable composite base pan provides added strength while resisting rust and corrosion, as well as reducing sound and vibration.
  • Isolated Compressor Compartment – A molded composite bulkhead isolates the refrigeration components and the compressor from the rest of the unit, reducing sound and vibration.
  • Lower Installed Cost – Designed to provide enhanced installability by featuring a slide-down control compartment that allows easy access to control components, along with angled service valves to reduce overall installation time and cost.
  • Factory Installed Filter-Drier – A factory installed, solid core liquid line filter-drier removes harmful debris and moisture from the system.
  • Easy Service Access – A full end, full service access panel with handle makes for easy entry to internal components.
  • Communications Capable – Requiring only a simple 4-wire installation, the communicating capability enables the use of the Touch Screen Communicating Control, allowing real time visibility of system operation and the use of diagnostic features, while still maintaining the ability to function with a traditional thermostat.
  • Agency Listed – Safety certified by CSA to UL 1995/CSA 22.2. Performance certified to ANSI/AHRI Standard 210/240 in accordance with the Unitary Small Equipment certification program.

The Premium Series AL6B models are the outdoor part of a versatile air conditioning system. They are designed to be custom matched with one of our complete line of evaporator sections, each designed to serve a specific function. Matching air handlers are available for upflow, downflow, and horizontal left or right applications to provide a complete system. Alternately, add-on coils are available for use with modular air handlers or upflow, downflow, and horizontal furnaces. Electric heaters and field installed accessories are also available as needed.

Download Fraser-Johnston AL6B-Series
16-SEER Air Conditioner Literature




Fraser-Johnston Acclimate™
18-SEER Air Conditioners

Fraser-Johnston AL8B-Series 18-SEER air conditioners

  • AL8B-Series: 
    Premium 18-SEER R410A Split-System Air Conditioners
    (2 – 5 tons)

Energy Star Certified
  • Superior Coil Protection – A stamped, decorative metal coil guard completely protects the coil from debris and other damaging material.
  • Protected Compressor – The compressor is safeguarded against abnormal pressures and temperatures by an internal pressure relief valve, an internal temperature sensor, and factory high and low pressure system controls. A factory installed liquid line filter-drier further protects the compressor against moisture and debris.
  • Environmentally Friendly Refrigerant – The next generation refrigerant R-410A delivers environmentally friendly performance with zero ozone depletion.
  • Durable Finish – An automotive quality finish provides the ultimate protection from harmful UV rays and rust creep, ensuring a long-lasting, high quality appearance. A powder-paint topcoat is applied over a baked-on primer using a galvanized, zinc coated steel base material. The result is a finish that has been proven in testing to provide 33% greater durability than conventional powder-coat finishes.
  • Sound Reducing System – Features combination of swept-wing fan, composite base pan, isolated compressor compartment, and single-stage compressor to reduce overall sound to a mere whisper.
  • Low RPM Fan Motor – Helps to reduce airflow noise.
  • Swept Wing Fan – A fan design boasting technology adapted from aeronautic and defense engineering provides for whisper-quiet operation by allowing air to flow smoothly and efficiently across the fan tips.
  • Composite Base Pan – The strong and durable composite base pan provides added strength while resisting rust and corrosion, as well as reducing sound and vibration.
  • Isolated Compressor Compartment – A molded composite bulkhead isolates the refrigeration components and the compressor from the rest of the unit, reducing sound and vibration.
  • Lower Installed Cost – Designed to provide enhanced installability by featuring a slide-down control compartment that allows easy access to control components, along with angled service valves to reduce overall installation time and cost.
  • Factory Installed Filter-Drier – A factory installed, solid core liquid line filter-drier removes harmful debris and moisture from the system.
  • Easy Service Access – A full end, full service access panel with handle makes for easy entry to internal components.
  • Communications Capable – Requiring only a simple 4-wire installation, the communicating capability enables the use of the Touch Screen Communicating Control, allowing real time visibility of system operation and the use of diagnostic features, while still maintaining the ability to function with a traditional thermostat.
  • Agency Listed – Safety certified by CSA to UL 1995/CSA 22.2. Performance certified to ANSI/AHRI Standard 210/240 in accordance with the Unitary Small Equipment certification program.

The Premium Series AL8B models are the outdoor part of a versatile air conditioning system. They are designed to be custom matched with one of our complete line of evaporator sections, each designed to serve a specific function. Matching air handlers are available for upflow, downflow, and horizontal left or right applications to provide a complete system. Alternately, add-on coils are available for use with modular air handlers or upflow, downflow, and horizontal furnaces. Electric heaters and field installed accessories are also available as needed.

Download Fraser-Johnston AL8B-Series
18-SEER Air Conditioner Literature



HEAT PUMPS


Fraser-Johnston Base-Series
13-SEER Heat Pumps

Fraser-Johnston THGD-Series 13-SEER Heat Pumps

  • THGD-Series: 
    13-SEER R410A single-phase Heat Pumps
    (1-1/2 – 5 tons)

  • Small Footprint – extremely lightweight with a compact footprint, it will be a perfect fit for any application.
  • Quality Condenser Coils – The coil is constructed of copper tubing and enhanced aluminum fins for increased performance.
  • Coil Protection – Coils are protected from damage by a polymer mesh applied between the coil face, and a coated steel coil guard.
  • Protected Compressor – The compressor is protected internally by a high pressure relief valve and a temperature sensor, and externally by the system high and low pressure switches. A factory installed liquid line filter-drier further protects the compressor against moisture and debris.
  • Environmentally Friendly Refrigerant – The next generation refrigerant R-410A delivers environmentally friendly performance with zero ozone depletion.
  • Durable Finish – The cabinet is made of G90-equivalent pre-painted steel, with special primer formulas and matte champagne texture to insure less fading when exposed to sunlight. The coated steel wire fan and coil guards and pre-treated, galvanized steel chassis components resist corrosion and rust creep.
  • Lower Installed Cost – Installation time and costs are reduced by easy power and control wiring connections. The unit is factory charged for a 15-foot lineset. The small base dimension means less space is required on the ground or roof.
  • Top Discharge – Warm air from the top mounted fan is blown up, away from the structure and any landscaping. This allows compact location on multi-unit applications.
  • Low Operating Sound Level – The upward air flow carries the normal operating noise away from the living area. The rigid top panel effectively isolates any motor sound. Isolator mounted compressor and the condenser coil muffle the normal fan motor and compressor operating sounds.
  • Low Maintenance – Long life, permanently lubricated motor-bearings need no annual servicing.
  • Easy Service Access – Fully exposed refrigerant connections and a single panel covering the electrical controls make for easy servicing of the unit.
  • Secured Service Valves – Secured, re-usable service valves are provided on both the liquid and vapor sweat connections for ease of evacuating and charging.
  • Agency Listed – Safety certified by CSA to UL 1995/CSA 22.2. Performance certified to ANSI/AHRI Standard 210/240 in accordance with the Unitary Small Equipment certification program.

The Fraser-Johnston Base-Series THGD models are the outdoor part of a versatile heat pump system. They are designed to be custom matched with one of our complete line of evaporator sections, each designed to serve a specific function. Matching air handlers are available for upflow, downflow, and horizontal left or right applications to provide a complete system. Alternately, add-on coils are available for use with modular air handlers or upflow, downflow, and horizontal furnaces. Electric heaters and field installed accessories are also available as needed. All heat pump models are Hybrid Heat compatible (requires accessory kit or compatible thermostat).

Download Fraser-Johnston Base-Series
13-SEER Heat Pump Literature




Fraser-Johnston LX-Series
14.5-SEER Heat Pumps

Fraser-Johnston TCJF-Series 14.5-SEER Heat Pumps

  • TCJF-Series: 
    14.5-SEER R410A single-phase Heat Pumps
    (1-1/2 – 5 tons)

Energy Star Certified
  • Small Footprint – The compact footprint is a perfect fit for any application.
  • Quality Condenser Coils – The coil is constructed of copper tubing and enhanced aluminum fins for increased performance.
  • Coil Protection – Coils are protected from damage by a slotted, stamped steel coil guard.
  • Protected Compressor – Compressors are protected internally by a high pressure relief valve and a temperature sensor, and externally by the system high and low pressure switches. A factory installed liquid line filter-drier further protects the compressor against moisture and debris.
  • Durable Finish – The cabinet is made of G90-equivalent galvanized steel, finished in a durable titanium colored powdercoat. The coated steel wire fan guard and pre-treated, galvanized steel chassis components resist corrosion and rust creep.
  • Lower Installed Cost – Installation time and costs are reduced by easy power and control wiring connections. The unit is factory charged for a 15-foot lineset. The small base dimension means less space is required on the ground or roof.
  • Top Discharge – Warm air from the top mounted fan is blown up, away from the structure and any landscaping. This allows compact location on multi-unit applications.
  • Quiet Operation – The compressor sound blanket and the swept wing fan blade keep sound to a minimum. The upward air flow carries the normal operating noise away from the living area. The rigid top panel effectively isolates any motor sound. Isolator mounted compressor and the condenser coil muffle the normal fan motor and compressor operating sounds. The rigid top panel effectively isolates any motor sound. Isolator mounted compressor and the condenser coil muffle the normal fan motor and compressor operating sounds.
  • Low Maintenance – Long life, permanently lubricated motor-bearings need no annual servicing.
  • Easy Service Access – Fully exposed refrigerant connections and a single panel covering the electrical controls make for easy servicing of the unit.
  • Advanced System Control –  These heat pumps feature a demand-defrost control system to provide optimal comfort and reliable operation over a wide range of conditions.
  • Secured Service Valves – Secured, re-usable service valves are provided on both the liquid and vapor sweat connections for ease of evacuating and charging.
  • Agency Listed – Safety certified by CSA to UL 1995/CSA 22.2. Performance certified to ANSI/AHRI Standard 210/240 in accordance with the Unitary Small Equipment certification program.
  • Energy Star Certified.

The Fraser-Johnston LX-Series THJF models are the outdoor part of a versatile heat pump system. They are designed to be custom matched with one of our complete line of evaporator sections, each designed to serve a specific function. Matching air handlers are available for upflow, downflow, and horizontal left or right applications to provide a complete system. Alternately, add-on coils are available for use with modular air handlers or upflow, downflow, and horizontal furnaces. Electric heaters and field installed accessories are also available as needed. Most models offer combinations that achieve Federal Tax Credit efficiency levels. All heat pump models are Hybrid Heat compatible (requires accessory kit or compatible thermostat).

Download Fraser-Johnston LX-Series
14.5-SEER Heat Pump Literature




Fraser-Johnston Acclimate™
16-SEER Heat Pumps

Fraser-Johnston HL6B-Series 16-SEER heat pumps

  • HL6B-Series: 
    Premium 16-SEER R410A Split-System Heat Pumps
    (2 – 5 tons)

Energy Star Certified
  • Superior Coil Protection – A stamped, decorative metal coil guard protects the tube-in-fin coil from debris and other damaging material.
  • Protected Compressor – The compressor is safeguarded against abnormal pressures and temperatures by an internal pressure relief valve, an internal temperature sensor, and factory high and low pressure system controls. A factory installed liquid line filter-drier further protects the compressor against moisture and debris.
  • Environmentally Friendly Refrigerant – TThe next generation refrigerant R-410A delivers environmentally friendly performance with zero ozone depletion.
  • Durable Finish – An automotive quality finish provides the ultimate protection from harmful UV rays and rust creep, ensuring a long-lasting, high quality appearance. A powder-paint topcoat is applied over a baked-on primer using a galvanized, zinc coated steel base material. The result is a finish that has been proven in testing to provide 33% greater durability than conventional powder-coat finishes.
  • Hot Heat Pump – An optional mode that slows the indoor fan for higher register air temperatures and premium comfort.
  • Sound Reducing System – Features combination of swept-wing fan, composite base pan, isolated compressor compartment, and single-stage compressor to reduce overall sound to a mere whisper.
  • Low RPM Fan Motor – Helps to reduce airflow noise.
  • Swept Wing Fan – A fan design boasting technology adapted from aeronautic and defense engineering provides for whisper-quiet operation by allowing air to flow smoothly and efficiently across the fan tips.
  • Composite Base Pan – The strong and durable composite base pan provides added strength while resisting rust and corrosion, as well as reducing sound and vibration.
  • Isolated Compressor Compartment – A molded composite bulkhead isolates the refrigeration components and the compressor from the rest of the unit, reducing sound and vibration.
  • Lower Installed Cost – Designed to provide enhanced installability by featuring a slide-down control compartment that allows easy access to control components, along with angled service valves to reduce overall installation time and cost. Factory charged for a 15 foot lineset.
  • Factory Installed Filter-Drier – A factory installed, solid core liquid line filter-drier removes harmful debris and moisture from the system.
  • Easy Service Access – A full end, full service access panel with handle makes for easy entry to internal components.
  • Communications Capable – Requiring only a simple 4-wire installation, the communicating capability enables the use of the Touch Screen Communicating Control, allowing real time visibility of system operation and the use of diagnostic features, while still maintaining the ability to function with a traditional thermostat.
  • Complete System Control – These heat pumps utilize a unique microprocessor defrost control system to provide optimal comfort as well as monitor the overall system for reliable operation. In the event improper operating conditions occur (high temperature and/or high pressure), the system will automatically shut the system down to extend the life of the heat pump. The defrost control features an internal memory to aid the technician in troubleshooting, reducing service time and cost.
  • Agency Listed – Safety certified by CSA to UL 1995/CSA 22.2. Performance certified to ANSI/AHRI Standard 210/240 in accordance with the Unitary Small Equipment certification program.

Download Fraser-Johnston HL6B-Series
16-SEER Heat Pump Literature




Fraser-Johnston Premium-Series
18-SEER Heat Pumps

Fraser-Johnston HL8B-Series 18-SEER heat pumps

  • HL8B-Series: 
    Premium 18-SEER R410A Split-System Heat Pumps
    (2 – 5 tons)

Energy Star Certified
  • Superior Coil Protection – A stamped, decorative metal coil guard protects the tube-in-fin coil from debris and other damaging material.
  • Protected Compressor – The compressor is safeguarded against abnormal pressures and temperatures by an internal pressure relief valve, an internal temperature sensor, and factory high and low pressure system controls. A factory installed liquid line filter-drier further protects the compressor against moisture and debris.
  • Environmentally Friendly Refrigerant – The next generation refrigerant R-410A delivers environmentally friendly performance with zero ozone depletion.
  • Durable Finish – An automotive quality finish provides the ultimate protection from harmful UV rays and rust creep, ensuring a long-lasting, high quality appearance. A powder-paint topcoat is applied over a baked-on primer using a galvanized, zinc coated steel base material. The result is a finish that has been proven in testing to provide 33% greater durability than conventional powder-coat finishes.
  • Hot Heat Pump – An optional mode that slows the indoor fan for higher register air temperatures and premium comfort.
  • Sound Reducing System – Features combination of swept-wing fan, composite base pan, isolated compressor compartment, and two-stage compressor to reduce overall sound to a mere whisper.
  • Low RPM Fan Motor – Helps to reduce airflow noise.
  • Swept Wing Fan – A fan design boasting technology adapted from aeronautic and defense engineering provides for whisper-quiet operation by allowing air to flow smoothly and efficiently across the fan tips.
  • Composite Base Pan – The strong and durable composite base pan provides added strength while resisting rust and corrosion, as well as reducing sound and vibration.
  • Isolated Compressor Compartment – A molded composite bulkhead isolates the refrigeration components and the compressor from the rest of the unit, reducing sound and vibration.
  • Lower Installed Cost – Designed to provide enhanced installability by featuring a slide-down control compartment that allows easy access to control components, along with angled service valves to reduce overall installation time and cost.
  • Factory Installed Filter-Drier – A factory installed, solid core liquid line filter-drier removes harmful debris and moisture from the system.
  • Easy Service Access – A full end, full service access panel with handle makes for easy entry to internal components.
  • Communications Capable – Requiring only a simple 4-wire installation, the communicating capability enables the use of the Touch Screen Communicating Control, allowing real time visibility of system operation and the use of diagnostic features, while still maintaining the ability to function with a traditional thermostat.
  • Agency Listed – Safety certified by CSA to UL 1995/CSA 22.2. Performance certified to ANSI/AHRI Standard 210/240 in accordance with the Unitary Small Equipment certification program.

The Fraser-Johnston Premium-Series HL8B models are the outdoor part of a versatile heat pump system. They are designed to be custom matched with one of our complete line of evaporator sections, each designed to serve a specific function. Matching air handlers are available for upflow, downflow, and horizontal left or right applications to provide a complete system. Alternately, add-on coils are available for use with modular air handlers or upflow, downflow, and horizontal furnaces. Electric heaters and field installed accessories are also available as needed. All heat pump models are Hybrid Heat compatible.

Download Fraser-Johnston HL8B-Series
18-SEER Heat Pump Literature



AIR HANDLERS


Fraser-Johnston MP-Series
Air Handlers

Fraser-Johnston MP-Series Air Handlers

  • MP-Series: 
    Modular Air Handlers
    (2 – 5 tons)
  •  
  • Supercedes MA-series
  • New
  • RC2 –  Rigid Case Construction interior endoskeleton provides structural support, flush sides, and locks in insulation.
  • Powder-painted – G30 galvanized steel case provides a coated edge that resists corrosion and rust creep.
  • Quality Construction – Structural components are made of Aluminum or G90 galvanized steel to prevent corrosion.
  • Improved Insulation Design – Single piece with no external screws to reduce thermal transmission paths to prevent sweating. Foil faced insulation for ease of cleaning.
  • Case Depth – These models have 20.5" casing which provide ease of attic access and tight applications.
  • Factory Sealed – Achieves 2% or less total airflow leakage rate at duct leakage test conditions in positive and negative pressure for system airflow verification.
  • Electric Heat Kits –  6HK series of field installed electric heat kits are available for installation-friendly and easy service applications. These 6HK kits may be used in multiple application for air handlers, modular blowers, and residential package units.
  • Blowers – All models use direct-drive, multi-speed PSC motors.

This unique modular system allows the flexibility to handle any application. These versatile MP blowers may be used for up-flow, down-flow, or horizontal left or right applications. They may be combined with cased coils to function as a cooling only unit or with a heat pump including electric heat for 1 and 3 phase applications. The MP blower and 6HK electric heaters can be used as a stand alone electric furnaces.

Download Fraser-Johnston New Air Handlers Literature



Fraser-Johnston MA-Series
Air Handlers

Fraser-Johnston MA-Series Air Handlers

  • MA-Series: 
    Modular Air Handlers
    (2 – 5 tons)
  •  
  • Superceded by MP-series
  • Blowers – MA series models to match any air flow (2 to 5 tons) or voltage requirement (115v, 230v, and 460v models are available). The compact size allows easy installation. Blowers are sized to deliver design air quantity both efficiently and quietly. The direct-drive, multi-speed blower motors provide a selection of air quantities to match any application. All models include a one-minute blower off delay as standard to enhance system efficiency ratings.
  • Cabinets – The durable, pre-painted steel protects the unit against rust and corrosion. All models have 1 inch foil face fiber glass insulation.
  • 4HK Series Electric Heaters – Both single and three phase electric heater models are available to match any requirement. All heaters include nickel-chromium elements with a 5-year limited warranty on 1 ø heating elements and 1 year limited warranty on 3 ø heating elements. Sequencers are provided to control heaters in all models. Circuit breakers are used in 208/230 volt, single phase heaters of 13 KW and larger. Models equipped with circuit breakers may be altered in the field to use multi-source power supply. Over-temperature limit switches provide protection from airflow loss.
  • Limitations – These units must be wired and installed in accordance with all national and local safety codes.

This unique modular system allows the flexibility to handle any application. These versatile Fraser-Johnston MA blowers may be used for up-flow, down-flow, or horizontal left or right applications. They may be combined with cased coils to function as a cooling only unit or with a heat pump including electric heat for 1 and 3 phase applications. The MA blower and 4HK electric heaters can be used as a stand alone electric furnaces.

Download Fraser-Johnston Air Handlers Literature



Fraser-Johnston MV-Series
Air Handlers

Fraser-Johnston MV-Series Air Handlers

  • MV-Series: 
    Variable-Speed, Modular Air Handlers
    (3 – 5 tons)
  • Blowers – Models to match any air flow or voltage requirement. The compact size allows easy installation. Blowers are sized to deliver design air quantity both efficiently and quietly. The motors provide a selection of air quantities to match any application. All models include a one-minute blower off delay as standard to enhance system efficiency ratings.
  • Cabinets – The durable, pre-painted steel protects the unit against rust and corrosion. All models have 1 inch foil face fiber glass insulation.
  • Electric Heaters – Both single and three phase electric heater models are available to match any requirement. All heaters include nickel-chromium elements with a 5-year limited warranty on 1 ø heating elements and 1 year limited warranty on 3 ø heating elements. Sequencers are provided to control heaters in all models. Circuit breakers are used in 208/230 volt, single-phase heaters of 13 KW and larger.Models equipped with circuit breakers may be altered in the field to use multi-source power supply. Over-temperature limit switches provide protection from airflow loss.

This unique modular system allows the flexibility to handle any application. These versatile Fraser-Johnston MV blowers may be used for upflow, downflow, or horizontal left or right applications. They may be combined with cased coils to function as a cooling only unit or with a heat pump including electric heat for 1 and 3 phase applications. The MV blower section and 4HK series electric heaters can be used as stand alone electric furnaces.

Download Fraser-Johnston Air Handlers Literature



Fraser-Johnston AHR-Series
Air Handlers

Fraser-Johnston AHR-Series Air Handlers

  • AHR-Series: 
    Single-Piece Air Handlers
    (1.5 – 5 tons)
  • Thermal Expansion Valve – Provides the ultimate refrigerant control required for today’s high efficient systems. The UPG bolt-on TXV provides easy installation to convert the air handler to the required refrigerant, which is a true bolt-on design that does not require brazing to replace or install.
  • Insulated Cabinet – All air handler cabinets are thermally insulated with 3/4" foil faced insulation to prevent sweating.
  • Durable Finish Inside and Out – Air handler casings are made of pre-painted galvanized steel which provides a better paint to steel bond that resists corrosion and rust creep. All internal coil sheet metal parts are made of G60 galvanized or prepainted G30 galvainzed. All heaters include nickel-chromium elements with a 5-year limited warranty on 1 ø heating elements and 1 year limited warranty on 3 ø heating elements. Sequencers are provided to control heaters in all models. Circuit breakers are used in 208/230 volt, single-phase heaters of 13 KW and larger.Models equipped with circuit breakers may be altered in the field to use multi-source power supply. Over-temperature limit switches provide protection from airflow loss.
  • Filters – All models have internal filter racks provided for use with 1" thick standard size filters.
  • Electric Heat Kits – The 6HK series of field installed electric heat kits are available for installation friendly and easy service applications. These 6 HK kits are available from 2 to 25 kW heat capacity.
  • Blowers – All models use 3-speed PSC motors to provide cooling SEER rating versatility.

The AHR Air Handler line offers the ultimate in comfort, sound and application flexibility. The air handler is shipped ready to be installed in upflow, horizontal left or right position with minor adjustments. No special kits are required to install this deluxe product.

All residential air handlers and coils may use a TXV to provide our customers with the optimum performance and refrigerant control required for 13+ SEER systems. Air handlers are available with "Flex-coils" without a factory installed metering device, where for added flexibility, a R-22 or R-410A TXV can be field installed to meet your refrigerant choice.

Download Fraser-Johnston Air Handlers Literature



Fraser-Johnston AE-Series
Air Handlers

Fraser-Johnston AE-Series Air Handlers

  • AE-Series: 
    Single-Piece Air Handlers
    (1.5 – 5 tons)
  •  
  • Supercedes AHE-series
  • New
  • RC2 – Rigid Case Construction interior endoskeleton provides structural support, flush sides, and locks in insulation.
  • Powder-Painted – G30 galvanized steel case provides a coated edge that resists corrosion and rust creep.
  • MaxAlloyTM Coil – Long life aluminum coils built to deliver lasting performance, efficiency and reliability.
  • Quality Construction – Structural components are made of Aluminum or G90 galvanized steel to prevent corrosion.
  • Improved Insulation Design – Single piece with no external screws to reduce thermal transmission paths to prevent sweating. Foil faced insulation for ease of cleaning.
  • Thermostatic Expansion Valve – Bolt-on TXV provides easy installation to convert the indoor coil to the required refrigerant and does not require brazing to replace or install. Select models are available with factory installed TXV.
  • Case Depth – These models have 20.5" casing which provide ease of attic access and tight applications.
  • Thermoset Drain Pan – Positive slope for drainage to reduce cause for potential mold or contaminants.
  • Factory Sealed – Achieves 2% or less total airflow leakage rate at duct leakage test conditions in positive and negative pressure for system airflow verification.
  • Enhanced Filter Rack – All models have an internal filter rack for use with 1” thick standard size filters.
  • Electric Heat Kits – 6HK series of field installed electric heat kits are available for installation-friendly and easy service applications. These 6HK kits may be used in multiple application for air handlers, modular blowers, and residential package units.
  • High Efficiency Blowers – All models use high efficiency brushless DC motors to provide cooling SEER rating enhancement.

The AE Air Handler line offers the ultimate in comfort, sound and application flexibility. This unit may be used for upflow, downflow, horizontal right, or horizontal left applications. No special kits are required to install this deluxe product.

All residential air handlers and coils may use a TXV to provide our customers with the optimum performance and refrigerant control. Air handlers maybe shipped with "Flex-coils" without a factory installed metering device or factory installed TXV. For added flexibility, an R-22 or R-410A TXV or orifice can be field installed to meet your refrigerant choice.

Download Fraser-Johnston New Air Handlers Literature



Fraser-Johnston AHE-Series
Air Handlers

Fraser-Johnston AHE-Series Air Handlers

  • AHE-Series: 
    Variable-Speed, Single-Piece Air Handlers
    (1.5 – 5 tons)
  •  
  • Superceded by AE-series
  • Thermal Expansion Valve – Provides the ultimate refrigerant control required for today’s high efficient systems. The UPG bolt-on TXV provides easy installation to convert the air handler to the required refrigerant, which is a true bolt-on design that does not require brazing to replace or install.
  • Insulated Cabinet – All air handler cabinets are thermally insulated with 3/4" foil faced insulation to prevent sweating.
  • Durable Finish Inside and Out – Air handler casings are made of pre-painted galvanized steel which provides a better paint to steel bond that resists corrosion and rust creep. All internal coil sheet metal parts are made of G60 galvanized or prepainted G30 galvainzed. All heaters include nickel-chromium elements with a 5-year limited warranty on 1 ø heating elements and 1 year limited warranty on 3 ø heating elements. Sequencers are provided to control heaters in all models. Circuit breakers are used in 208/230 volt, single-phase heaters of 13 KW and larger.Models equipped with circuit breakers may be altered in the field to use multi-source power supply. Over-temperature limit switches provide protection from airflow loss.
  • Filters – All models have internal filter racks provided for use with 1" thick standard size filters.
  • Electric Heat Kits – The 6HK series of field installed electric heat kits are available for installation friendly and easy service applications. These 6 HK kits are available from 2 to 25 kW heat capacity.
  • High Efficiency Blowers – All models use high efficiency brushless DC motors to provide cooling SEER rating enhancement.

The AHE Air Handler line offers the ultimate in comfort, sound and application flexibility. The air handler is shipped ready to be installed in upflow, horizontal left or right position with minor adjustments. No special kits are required to install this deluxe product.

All residential air handlers and coils may use a TXV to provide our customers with the optimum performance and refrigerant control required for 13+ SEER systems. Air handlers are available with "Flex-coils" without a factory installed metering device, where for added flexibility, a R-22 or R-410A TXV can be field installed to meet your refrigerant choice.

Download Fraser-Johnston Air Handlers Literature


EVAPORATOR COILS


Fraser-Johnston PC-Series
Evaporator Coils

Fraser-Johnston PC-Series Evaporator Coils

  • PC-Series: 
    Half-Cased Evaporator Coils
    (2 – 5 tons)
  • Thermal Expansion Valve – Provides flexibility to use R-22 or R-410A refrigerant. A true bolt-on TXV, valve assembly and equalizer tube is available with no brazing required. TXV and sensing bulb are mounted inside the cased coil cabinet. (Must be field supplied for all "Flex-coils").
  • Insulated Cabinet – All evaporator coil cabinets are thermally insulated with foil faced insulation to prevent sweating.
  • Internally Clean – All evaporator coils are factory leak-tested, dehydrated, sealed and shipped with a holding charge.
  • Durable Finish Inside and Out – Coil casings are made of pre-painted steel. The pre-treated flat galvanized steel provides a better paint to steel bond, which resist corrosion and rust creep. All internal metal parts are made of G90 pre-painted steel i.e. triangular plates, top plates, horizontal supports etc. (Coil header plates are non-painted due to the brazing process during production.).
  • Optimum Heat Transfer – Using the latest in heat transfer technology, staggered rows of copper tubes are mechanically expanded into aluminum fins to provide optimum air to surface contact for ample moisture removal as well as high performance ratings.

These Fraser-Johnston PC-Series evaporator coils are designed to be installed with Fraser-Johnston furnaces and to be matched with Fraser-Johnston cooling and heat pump outdoor units. With an indusrty unique partial case design, these PC coils are intended for upflow applications where height limitations in the application prevent the installation of full cased coils. The partial case design allows the top section of the evaporator coil to be installed in the duct or plenum and still provide the required heat transfer for the high efficiency system matches.

All evaporator coils can be applied with orifices and may require a TXV for system ratings with certain outdoor units. Refer to the Technical Guide for the outdoor unit selected as part of your system.

Coils are provided as "Flex-coils" without a factory installed metering device. For added application flexibility, a R-22 or R-410A TXV is field installed on "Flex-coils" to meet your refrigerant choice.

Download Fraser-Johnston PC-Series Evaporator Coils Literature



Fraser-Johnston CF-Series
Evaporator Coils

Fraser-Johnston CF-Series Evaporator Coils

  • CF-Series: 
    Full-Cased Evaporator Coils
    (2 – 5 tons)
  •  
  • Supercedes FC-series
  • New
  • RC2 – Rigid Case Construction interior endoskeleton provides structural support, flush sides, and locks in insulation.
  • Powder-painted – G30 galvanized steel case provides a coated edge that resists corrosion and rust creep.
  • MaxAlloyTM Coil – Long life aluminum coils built to deliver lasting performance, efficiency and reliability.
  • Quality Construction – Structural components are made of Aluminum or G90 galvanized steel to prevent corrosion.
  • Improved Insulation Design – Single piece with no external screws to reduce thermal transmission paths to prevent sweating. Foil faced insulation for ease of cleaning.
  • Thermostatic Expansion Valve – Bolt-on TXV provides easy installation to convert the indoor coil to the required refrigerant and does not require brazing to replace or install. Select models are available with factory installed TXV.
  • Case Depth – These models have 20.5" casing which provide ease of attic access and tight applications.
  • Thermoset Drain Pan – Positive slope for drainage to reduce cause for potential mold or contaminants.

These CF-series are MaxAlloy aluminum indoor coils and are designed to be installed with furnaces and modular blowers to be matched with cooling and heat pump outdoor units.

All indoor coils can be applied with orifices or TXV which maybe require for system ratings with certain outdoor units. Refer to the Technical Guide for the outdoor unit selected as part of your system.

Coils maybe provided as "Flex-coils" without a factory installed metering device or factory installed TXV. For added application flexibility, a R22 or R410A TXV is field installed on "Flex-coils" to meet your refrigerant choice.



Fraser-Johnston FC-Series
Evaporator Coils

Fraser-Johnston FC-Series Evaporator Coils

  • FC-Series: 
    Full-Cased Evaporator Coils
    (2 – 5 tons)
  •  
  • Superceded by CF-series
  • Thermal Expansion Valve – Provides flexibility to use R-22 or R-410A refrigerant. A true bolt-on TXV, valve assembly and equalizer tube is available with no brazing required. TXV and sensing bulb are mounted inside the cased coil cabinet. (Must be field supplied for all "Flex-coils").
  • Insulated Cabinet – All evaporator coil cabinets are thermally insulated with foil faced insulation to prevent sweating.
  • Internally Clean – All evaporator coils are factory leak-tested, dehydrated, sealed and shipped with a holding charge.
  • Durable Finish Inside and Out – Coil casings are made of pre-painted steel. The pre-treated flat galvanized steel provides a better paint to steel bond, which resist corrosion and rust creep. All internal metal parts are made of G90 pre-painted steel i.e. triangular plates, top plates, horizontal supports etc. (Coil header plates are non-painted due to the brazing process during production.).
  • Optimum Heat Transfer – Using the latest in heat transfer technology, staggered rows of copper tubes are mechanically expanded into aluminum fins to provide optimum air to surface contact for ample moisture removal as well as high performance ratings.

These Fraser-Johnston FC-Series evaporator coils are designed to be installed with Fraser-Johnston furnaces and to be matched with Fraser-Johnston cooling and heat pump outdoor units. With an indusrty unique partial case design, these PC coils are intended for upflow applications where height limitations in the application prevent the installation of full cased coils. The partial case design allows the top section of the evaporator coil to be installed in the duct or plenum and still provide the required heat transfer for the high efficiency system matches.

All evaporator coils can be applied with orifices and may require a TXV for system ratings with certain outdoor units. Refer to the Technical Guide for the outdoor unit selected as part of your system.

Coils are provided as "Flex-coils" without a factory installed metering device. For added application flexibility, a R-22 or R-410A TXV is field installed on "Flex-coils" to meet your refrigerant choice.

Download Fraser-Johnston FC-Series Evaporator Coils Literature



Fraser-Johnston CM-Series
Evaporator Coils

Fraser-Johnston CM-Series Evaporator Coils

  • CM-Series: 
    Multi-Position Evaporator Coils
    (2 – 5 tons)
  •  
  • Supercedes MC-series
  • New
  • RC2 – Rigid Case Construction interior endoskeleton provides structural support, flush sides, and locks in insulation.
  • Powder-painted – G30 galvanized steel case provides a coated edge that resists corrosion and rust creep.
  • MaxAlloyTM Coil – Long life aluminum coils built to deliver lasting performance, efficiency and reliability.
  • Quality Construction – Structural components are made of Aluminum or G90 galvanized steel to prevent corrosion.
  • Improved Insulation Design – Single piece with no external screws to reduce thermal transmission paths to prevent sweating. Foil faced insulation for ease of cleaning.
  • Thermostatic Expansion Valve – Bolt-on TXV provides easy installation to convert the indoor coil to the required refrigerant and does not require brazing to replace or install. Select models are available with factory installed TXV.
  • Case Depth – These models have 20.5" casing which provide ease of attic access and tight applications.
  • Thermoset Drain Pan – Positive slope for drainage to reduce cause for potential mold or contaminants.

These CM-series indoor coils are designed to be installed with furnaces and modular blowers to be matched with cooling and heat pump outdoor units in all four configurations - upflow, downflow, and horizontal left or right.

All indoor coils can be applied with orifices or TXV which maybe require for system ratings with certain outdoor units. Refer to the Technical Guide for the outdoor unit selected as part of your system.

Coils maybe provided as "Flex-coils" without a factory installed metering device or factory installed TXV. For added application flexibility, a R22 or R410A TXV is field installed on "Flex-coils" to meet your refrigerant choice.



Fraser-Johnston MC-Series
Evaporator Coils

Fraser-Johnston MC-Series Evaporator Coils

  • MC-Series: 
    Full-Cased, Multi-Position Evaporator Coils
    (2 – 5 tons)
  •  
  • Superceded by CM-series
  • Thermal Expansion Valve – Provides flexibility to use R-22 or R-410A refrigerant. A true bolt-on TXV, valve assembly and equalizer tube is available with no brazing required. TXV and sensing bulb are mounted inside the cased coil cabinet. (Must be field supplied for all "Flex-coils").
  • Insulated Cabinet – All evaporator coil cabinets are thermally insulated with foil faced insulation to prevent sweating.
  • Internally Clean – All evaporator coils are factory leak-tested, dehydrated, sealed and shipped with a holding charge.
  • Durable Finish Inside and Out – Coil casings are made of pre-painted steel. The pre-treated flat galvanized steel provides a better paint to steel bond, which resist corrosion and rust creep. All internal metal parts are made of G90 pre-painted steel i.e. triangular plates, top plates, horizontal supports etc. (Coil header plates are non-painted due to the brazing process during production.).
  • Optimum Heat Transfer – Using the latest in heat transfer technology, staggered rows of copper tubes are mechanically expanded into aluminum fins to provide optimum air to surface contact for ample moisture removal as well as high performance ratings.

These Fraser-Johnston MC-Series evaporator coils are designed to be installed with Fraser-Johnston furnaces and modular blowers to be matched with Fraser-Johnston cooling and heat pump outdoor units in all four configurations – upflow, downflow, and horizontal left or right.

All evaporator coils can be applied with orifices and may require a TXV for system ratings with certain outdoor units. Refer to the Technical Guide for the outdoor unit selected as part of your system.

Coils are provided as "Flex-coils" without a factory installed metering device. For added application flexibility, a R-22 or R-410A TXV is field installed on "Flex-coils" to meet your refrigerant choice.

Download Fraser-Johnston MC-Series Evaporator Coils Literature





4 Convienent Locations Throughout New Jersey!


HEADQUARTERS

9 Gloria Lane
Fairfield, NJ 07004
(973) 227-4840
Fax: (973) 227-8750

BRANCH

245 Lackland Drive West
Middlesex, NJ 08846
(732) 560-0340
Fax: (732) 560-8691

BRANCH

110 Gaither Drive–Unit D
Mt. Laurel, NJ 08054
(856) 778-0204
Fax: (856) 778-0542

BRANCH

750 Airport Road
Lakewood, NJ 08701
(732) 370-9111
Fax: (732) 370-9444